|
Facilità d'uso
. . . . . . . .2 Installation Instructions . .3–12 Step-by-step instructions . . .6–12 Operating Instructions Breaking a salt bridge . . . . . . .14 Cleaning the nozzle and venturi assembly . . . . . . . . . . .14 Features . . . . . . . . . . . . . . . . . .15 Service . . . . . . . . . . . . .13, 16–18 Water softener system . . . .13–18 Care and Cleaning . . . . . . . .19 Troubleshooting Tips . . . .20–22 Consumer Support Consumer Support . .Back Cover Parts list/catalog . . . . . . . .24–27 Warranty (U.S.) . . . . . . . . . . . .28 Warranty (Canada) . . . . . . . . .29 Water Softening System Owner’s Manual & Installation Instructions Models GXSF35E, GXSF39E Sistema Suavizante de Agua Manual del Propietario e Instrucciones de Instalacion Modelos GXSF35E, GXSF39E La seccion en espanol empieza en la pagina 31 System tested and certified by NSF International against NSF/ANSI Standard 44 for the chemical reduction claims specified on the performance data sheet. Sistema probado y certificado por NSF International contra norma 44 de NSF/ANSI para las afirmaciones de reduccion de los productos quimicos especificadas en la hoja de datos de funcionamiento. Write the model and serial numbers here: Model # ____________________________ Serial # ____________________________ To find these numbers, lift the cover and look on the rim below the control panel. 7247174 215C1173P010 49-50151 02-05 JR IMPORTANT SAFETY INFORMATION. READ ALL INSTRUCTIONS BEFORE USING. WARNING! For your safety, the information in this manual must be followed to minimize the risk of electric shock, property damage or personal injury. SAFETY PRECAUTIONS Check and comply with your state and local codes. You must follow these guidelines. Use care when handling the water softening system. Do not turn upside down, drop, drag or set on sharp protrusions. Water softening systems using sodium chloride (salt) for recharge add sodium to the water. Persons on sodium restricted diets should consider the added sodium as part of their overall intake. Potassium chloride can be used as an alternative to sodium chloride in your softener. The water softening system works on 24 volt-60 Hz electrical power only. Be sure to use only the included transformer. Transformer must be plugged into an indoor 120 volt, grounded outlet only. PROPER INSTALLATION Use clean water softening salts only, at least 99.5% pure. NUGGET, PELLET or coarse SOLAR salts are recommended. Do not use rock, block, granulated or ice cream making salts. They contain dirt and sediments, or mush and cake, and will create maintenance problems. Keep the salt hole cover in place on the softener unless servicing the unit or refilling with salt. WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. This water softening system must be properly installed and located in accordance with the Installation Instructions before it is used. Install or store where it will not be exposed to temperatures below freezing or exposed to any type of weather. Water freezing in the system will break it. Do not attempt to treat water over 100°F. Do not install in direct sunlight. Excessive sun or heat may cause distortion or other damage to non-metallic parts. Properly ground to conform with all governing codes and ordinances. Use only lead-free solder and flux for all sweat- solder connections, as required by state and federal codes. The water softening system requires a minimum water flow of three gallons per minute at the inlet. Maximum allowable inlet water pressure is 125 psi. If daytime pressure is over 80 psi, nighttime pressure may exceed the maximum. Use a pressure reducing valve to reduce the flow if necessary. Softener resins may degrade in the presence of chlorine above 1 ppm. If you have chlorine in excess of this amount, you may experience reduced life of the resin. In these conditions, you may wish to consider purchasing a GE point-of-entry household filtration system with a chlorine reducing filter. WARNING: Discard all unused parts and packaging material after installation. Small parts remaining after the installation could be a choke hazard. READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY. SAVE THESE INSTRUCTIONS Installation instructions. GEAppliances.com CAUTION: Certain plumbing skills are needed for installation. If you are unsure about any part of the installation of this product, consult a professional plumber. Unpacking and Inspection Be sure to check the entire softener for any shipping damage or parts loss. Also note damage to the shipping cartons. Contact the transportation company for all damage and loss claims. The manufacturer is not responsible for damages in transit. Small parts needed to install the softener are packaged either in a bag or on a cardboard sheet. To avoid loss of the small parts, keep them packaged until you are ready to use them. Be sure not to discard components hidden in p...
Questo manuale è adatto anche per i modelli :Depuratori d - GXSF39E (1.2 mb)