valutazioni - 3, GPA: 3.7
(
)
)
|
Facilità d'uso
Allow the Rota filter to stop in its own time. • Use only the original Philips filters. • Do not obstruct the air inlet and air outlet grilles. Do not place the appliance on a soft surface such as a bed or couch. • Keep the mains cord away from heated surfaces. • If the mains cord of this appliance is damaged, it must only be replaced by Philips or their service representative, as special tools and/or parts are required. • Save these instructions for further reference. • The appliance has an influence upon the air circulation in the room. In general, it is not advisable to use it near an open hearth fire. • For quick air cleaning, set the speed selector to the “turbo” setting. After approximately half an hour, set the switch to the position for normal speed. • To maintain clean, fresh air in your room all the time, it is best to run your machine continuously on low or normal speed, depending on room size and the degree to which the air tends to contaminate. • Clean and replace your filters regularly, especially if the appliance is used in a smoky environment. How to clean or replace the filters General advice • Remove and clean the Pre-filter and the Rota filter at least every two months. • Remove and replace the Hepa filters as soon as the colour of their undersides corresponds to the darkest grey on the “Filter full” indicator. • Check the filters right away if the appliance becomes noisier. Clean and/or replace the filters if necessary. It may be necessary to clean the filters more frequently. This depends on: • How much the appliance has been used (operation time, speed). • The condition of the air to be filtered. Removing the filters - Set the speed selector to position O (fig. 9). General description (fig. 8) A Air inlets (3) B Pre-filter C Rota filter D Fixing nut for Rota filter E Hepa filters type HR 4320: 2 filters type HR 4330: 3 filters F Pilot light "On" G Air outlet H Speed control O = off • = low speed • = normal speed turbo = high speed I "Filter full" indicator J Handle K Cord storage -Remove the mains plug from the wall socket. -Remove the front cover (fig. 10). -Remove the Hepa filters (fig. 11). -Turn the Hepa filters. -Compare the colour of their undersides with the colours on the “Filter full” indicator (fig. 12). -Replace the Hepa filters as soon as the colour of their undersides corresponds to the darkest grey on the “Filter full” indicator (fig. 13). -Remove the Pre-filter (fig. 14). -Remove the Rota filter (fig. 15). To place the filters back reverse this process. Safety lock The front cover has a safety lock which prevents you from opening the cover whilst the Air Cleaner is switched on. The safety lock also prevents you from switching on if the front cover is removed. 5 Cleaning the Pre-filter and the Rota filter -Wash (fig. 16) or vacuum clean the Pre-filter. You can remove fluff or hairs e.g. using a soft brush. -Wash (fig. 17) or vacuum clean the Rota filter. If washed with a detergent, rinse the filters with clean warm water (fig. 18). Allow the filters to air-dry thoroughly (fig. 19) before reassembly. The Rota filter can also be washed in a dishwasher. Replacement Hepa filters New Hepa filters are available at your dealer under number HR 4920. Automatic overheating safety device To prevent damage and reduce safety risks the overheating safety device switches off the fan motor if it becomes too hot. To indicate that the appliance is still in switched- on position and connected to the mains, the pilot light will remain on. If this happens: -Set the speed selector to position O (= Off). -Remove the mains plug from the wall socket. (The pilot light goes out.) -Wait for the motor to cool down (approx. 15 minutes). -Open the appliance. Check that the filters are not blocked and that nothing is obstructing the airflow. -Check that the Rota filter can rotate freely if moved by hand (fig. 20). -Close the appliance. Put the mains plug back into the wall socket and switch on. If the automatic overheating device is activated repeatedly, it is advisable to take the appliance to your dealer for technical inspection. Francais Si vous voulez eviter des problemes de respiration, il faut avant tout que l’air dans votre maison soit pur. Votre epurateur d’air Philips permet une epuration efficace de l’air: 99% des particules en suspension dans l’air de votre habitation sont eliminees, y compris les allergenes, comme la poussiere de maison, le pollen, et meme des virus et des bacteries. Ces particules n’ont aucune utilite pour le corps humain. Certaines d’entre elles sont meme extremement nuisibles, pouvant causer de graves troubles et maladies. Les dimensions des particules varient de 0,1 a 100 microns. (1 micron = 0,001 mm). Mesures supplementaires • Si vous habitez dans un environnement urbain, n’ouvrez pas les fenetres pendant les heures de circulation intense ou en cas de forte pollution de l’air (p.ex. provenant d’usines). • Passez regulierement l’aspirateur dans votre habitation. Si vous...
Questo manuale è adatto anche per i modelli :Aria - HR 4320/30 (451.11 kb)