valutazioni - 2, GPA: 3.5
(
)
)
|
Facilità d'uso
Blow on thermistor at air flow monitor. 120 VAC should appear at multimeter. Stop blowing and voltage should disappear in 10 - 15 seconds. 4. If voltage did not appear (Step 3), disconnect power to power pack. Locate air flow switch and remove power pack cover. Disconnect the three-pin plastic connector. Jumper the two female pins (white wire to white-brown wire) as shown in Fig. 23. Reconnect power to power pack. Turn power switch “ON.” A. If 120 VAC appears at multimeter, replace air flow monitor. B. If 120 VAC does not appear on multimeter, problem is other than air flow monitor. Recheck all primary wiring. NOTE: The air flow monitor is designed to operate in the temperature range of 65° to 120° F. Operation outside this range is not recommended. 12 OZONE REDUCTION OZONE REDUCTIONOZONE REDUCTIONOZONE REDUCTIONOZONE REDUCTIONOZONE REDUCTION OZONE REDUCTIONOZONE REDUCTIONOZONE REDUCTIONOZONE REDUCTIONOZONE REDUCTION This power supply has a “hairpin” shaped jumper wire labeled W1 (see Fig 24) that can be cut and separated in case of such complaints. This will cause the power supply to limit the maximum operating power to a lower level. LINE WHT/BRN BLK W1 E3 E2 Cut and separate Ozone Reduction Jumper Ozone Reduction Jumper Ozone Reduction JumperOzone Reduction JumperOzone Reduction JumperOzone Reduction JumperOzone Reduction Jumper Figure 24 ELECTRONIC AIR CLEANER RETROFIT (ACR) KITS ELECTRONIC AIR CLEANER RETROFIT (ACR) KITSELECTRONIC AIR CLEANER RETROFIT (ACR) KITSELECTRONIC AIR CLEANER RETROFIT (ACR) KITSELECTRONIC AIR CLEANER RETROFIT (ACR) KITSELECTRONIC AIR CLEANER RETROFIT (ACR) KITS INSTALLATION INSTALLATIONINSTALLATIONINSTALLATIONINSTALLATIONINSTALLATION 1. Remove the two pre-filters from the package and insert into cabinet tracks opposite the furnace. These will be used to catch the larger particles that are in the air stream before entering the collecting cell. 2. Insert the two collecting cells into the cabinet behind the pre-filters. Be sure ionizing wires are directly behind the pre-filters so the particles can be charged as soon as the air leaves the pre-filters. 3. Remove cover plate on the power supply junction box and remove the knockout needed to bring the wire to the female receptacle. 4. Position receptacle with ground in the down position as shown in Fig 17 (page 7) and pull wires through the receptacle locator on the junction box. Snap the receptacle into the hole until secure. 5. Connect ground wire from receptacle and ground wire in kit to cabinet with rivet and washer as follows: a) Place washer on rivet b) Place terminal from ground wire on rivet c) Place terminal from receptacle ground wire on rivet d) Insert rivet in hole in junction box and secure. WIRING WIRINGWIRINGWIRINGWIRINGWIRING 5. For wiring installation (see page 7) and follow all wiring instructions 7, 8 and 9. 6. Install the power pack (see page 7) instruction 11. 7. For operation (see page 8 – Operation). Cabinet Pre-Filters Handle Contact Button Contact Button Collecting Cells 13 REPAIR PARTS REPAIR PARTSREPAIR PARTSREPAIR PARTSREPAIR PARTSREPAIR PARTS1 2 3 4 5 5 6 2 3 7 89 18 5 14 1310 11 12 REPAIR PARTSREPAIR PARTSREPAIR PARTSREPAIR PARTSREPAIR PARTS1 2 3 4 5 5 6 2 3 7 89 18 5 14 1310 11 12 14 REPAIR PARTS REPAIR PARTSREPAIR PARTSREPAIR PARTSREPAIR PARTSREPAIR PARTS REPAIR PARTSREPAIR PARTSREPAIR PARTSREPAIR PARTSREPAIR PARTS When ordering repair parts, always give the following information as shown in this list. 1. The PART NUMBER 2. The PART DESCRIPTION 3. The MODEL NUMBER 4. The NAME OF ITEM - Electronic Air Cleaner. Always order by “PART NUMBER” . . . Always order by “PART NUMBER” . . .Always order by “PART NUMBER” . . .Always order by “PART NUMBER” . . .Always order by “PART NUMBER” . . .Always order by “PART NUMBER” . . . Not by “ITEM NUMBER” Not by “ITEM NUMBER”Not by “ITEM NUMBER”Not by “ITEM NUMBER”Not by “ITEM NUMBER”Not by “ITEM NUMBER” ITEM NO. DESCRIPTION PART NUMBER SST1000 SST1400 SST1600 SST2000 1 Cabinet N/A N/A N/A N/A 2 Pre-Filter • F825-0431 • F825-0432 • F825-0337 • F825-0338 3 Collecting Cell • F811-0398 • F811-0397 • F811-0321 • F811-0319 4 Junction Box Cover F838-0072 F838-0072 F838-0072 F838-0072 5 * Screw #6 x 3/8 ---------- ----- ----- 6 Connector, Female F818-0053 F818-0053 F818-0053 F818-0053 7 Power Pack Assembly F858-1021 F858-1022 F858-1023 F858-1024 8 Cell Handle F832-0039 F832-0039 F832-0039 F832-0039 9 Ionizing Wire F843-0484 F843-0484 F843-0500 F843-0500 10 Light F844-0130 F844-0130 F844-0130 F844-0130 11 Switch F876-0202 F876-0202 F876-0202 F876-0202 12 Power Pack, Cabinet Only N/A N/A N/A N/A 13 Connector, Male F827-0026 F827-0026 F827-0026 F827-0026 14 Power Supply F858-1002 F858-1002 F858-1002 F858-1002 15 Cover, Power Pack F820-0098 F820-0098 F820-0220 F820-0220 16 † Manual 37-6373 37-6373 37-6373 37-6373 17 † Charcoal Filter (with mounting clips) F825-0466 • F825-0467 • F825-0468 • F825-0469 18 Air Flow Switch (monitor kit) F859-0381 F859-0381 F859-0381 F859-0381 * Standa...
Questo manuale è adatto anche per i modelli :Aria - SST1000 (565.52 kb)