valutazioni - 5, GPA: 3.2
(
)
)
|
Facilità d'uso
The flange D, to which the air exhaust pipe is connected, and a plug B, used to shut off the unused air outlet, are both supplied with the product. • This device may be installed in two different ways: 1. Fixing the hood to the lower part of the wall cabinet (Fig.2): -Make 4 holes in the wall cabinet respecting the measurements indicated in figures 2A-2C. -Position the hood underneath the wall cabinet and fix it into place using 4 screws (not supplied) suitable for the type of cabinet. - 11 2. Fixing the hood to the wall (Fig.2): -Make 4 holes in the wall cabinet respecting the measurements indicated in figures 2A-2B. -Hang the hood on the wall, using the 2 holes H, align it in a horizontal position and fix it definitively to the wall using the two lower safety holes I (Fig.2B). For the various installations use screws and screw anchors suited to the type of wall (e.g. reinforced concrete, plasterboard, etc.). If the screws and screw anchors are provided with the product, check that they are suitable for the type of wall on which the hood is to be fixed. • The hood is already prepared for the version with which it was ordered. The versions may be: - Extraction (Fig.1A-4). -Filter (Fig.1B-5-9). -If the hood is an extractor model, the lever C must be positioned as indicated in figure 4. -If the hood is a filter model, the lever C must be positioned as indicated in figure 5. • Extractor version: The appliance expels the fumes through an outside wall or a duct. It is necessary to buy a telescopic pipe in accordance with the standards in use (inflammable) and connect it to flange D (Fig.1B). The flange D is supplied with the product and should be fixed above the air outlet hole of the hood as indicated in figure 4. • Filtering version: To transform an extractor hood version into a filter hood version, contact your appliance dealer and ask for active charcoal filters. The filters should be fitted to the extraction assembly inside the hood, by centring them and rotating them 90 degrees, until they click into place (Fig.9). To do this, remove the grille D or the panels G (Fig.6-7). Close the air outlet opening with the plug B, as indicated in figure 5. USE AND MAINTENANCE • We recommend that the cooker hood is switched on before any food is cooked. We also recommend that the appliance is left running for 15 minutes after the food is cooked, in order to thoroughly eliminate all contaminated air. The effective performance of the cooker hood depends on constant maintenance; the anti-grease filter and the active carbon filter both require special attention. • The anti-grease filter is responsible retaining the grease particles suspended in the air, therefore it is subject to clogging with variable frequency according to the use of the appliance. -To prevent the danger of possible fires, at least every 2 months one must wash the anti-grease filters by hand using non-abrasive neutral liquid detergents or in the dishwasher at low temperatures and on short cycles. -After a few washes, colour alterations may occur. This does not give the right to claim their replacement. • The active carbon filters are used to purify the air that is sent back into the room and its function is to mitigate the unpleasant odours produced by cooking. -The non-regenerable active carbon filters must be replaced at least every 4 months. The saturation of the active charcoal depends on the more or less prolonged use of the appliance, on the type of kitchen and on the frequency with which anti- grease filter is cleaned. • Cleanthehoodfrequently,bothinternallyandexternally, using a cloth dampened with denatured alcohol or neutral liquid detergents that are non abrasive. • The lighting .system is designed for use during cooking and not for the prolonged general lighting of the room. The prolonged use of the lighting system significantly decreases the average duration of the bulbs. • If the appliance is equipped with courtesy lights it is possible to use them for general room lighting for a prolonged amount of time. • Attention: the non compliance with the hood cleaning warnings and with the replacement and cleaning of the filters entails risk of fires. One therefore recommends keeping to the suggested instructions. • Replacing the aluminium panels: To replace the aluminium panels, simply pull handle A as shown in Fig.7. • Replacing the acrylic or metal panels: To replace the acrylic or metal panels you need to first remove the grille D by pushing the two side buttons B inwards as indicated in figure 6. Remove the two filter clips B (Fig.8) and the acrylic or metal panel C. To reassemble the part, simply perform the procedure in reverse. • Replacing the halogen/incandescent lamps (Fig.3): Only use lamps of the same type and Wattage installed on the device. THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR EVENTUAL DAMAGES CAUSED BY BREACHING THE ABOVE WARNINGS. NEDERLANDS NL ALGEMEEN Lees aandachtig de inhoud van deze handleiding. Hierin staan belangrij...