valutazioni - 0, GPA: 0
(
)
)
|
Facilità d'uso
Never operate the extractor hood without a grease filter. Overheated fat or oil can easily catch fire. If you are cooking with fat or oil, e.g. chips, etc., never leave the cooker unattended. Carefully clean the extractor hood before switching on for the first time. Do not place any objects on the extractor hood. Operating procedure The most effective method of removing vapours produced during cooking is to: . Switch the ventilator ON as soon as you begin cooking. . Switch the ventilator OFF a few minutes after you have finished cooking. CONTROLS TYPE Switching the fan ON . Press the + button. Setting the required fan speed: . Press the + button. The fan speed is increased by one step. . Press the – button. The fan speed is reduced by one step. Switching the fan OFF: . Press the 0 button. Or: . Keep pressing the – button until the fan switches off. Intensive setting: Maximum power is obtained at the intensive setting. It is only required for short intervals. . Press the P push button. . If the intensive setting is not cancelled by hand, the fan will automatically switch back to step } after 5 minutes. Fan follow-on: . By pressing the T push button when fan is working, a count down is activated. After 15 minutes the fan will turn off. In this time there is a flashing led point in the display. Lighting: . The light can be switched on at any time, even though the fan is switched off. Filters and maintenance Grease filters: Metal filters are used to trap the greasy element of the vapours that develop during cooking. The filter mats are made from noncombustible metal. Caution: As the filter becomes more and more saturated with grease, not only does the risk of it catching fire increase but the efficiency of the extractor hood can also be adversely affected. Important: By cleaning the metal grease filters at appropriate intervals, the possibility of them catching fire as a result of a build-up of heat such as occurs when deep-fat frying or roasting is taking place, is reduced. Saturation indicator: F When the grease filter becomes saturated, the display symbol F appears. The grease filter should be cleaned straight away. Cleaning the metal grease filters: . In normal operation (1 to 2 hours daily), the metal grease filter must be cleaned after 8 to 10 weeks. . The filters can be cleaned in a dishwasher. It is however possible that they will become slightly discoloured. . The filter must be placed loosely, and NOT wedged, in the dishwasher. Important: Metal filters that are saturated with grease should not be washed together with other dishes etc. . When cleaning the filters by hand, soak them in hot soapy water first of all. Then brush the filters clean, rinse them thoroughly and leave the water to drain off. Removing and inserting the metal grease filters: Warning: The halogen bulbs must be switched off and cool. 1. Press the catch on the grease filters inwards and fold the filters down. Fig. 2. 2. Clean the filters. 3. Insert the clean filters back into the hood. 4. Cancel the F indication in the display. . Swith the motor off (stop position). . Press for some seconds at the same time 0 and T. A signal sounds and the display symbol F at the side goes out. If models feature side grease filters, remove these filters also, Fig. 3. 1. Unscrew the plastic holder. 2. Remove the grease filters. 3. Clean and re-insert the grease filters. Activated carbon filter: For neutralizing odours in recirculating mode. Saturation indicator: C When the activated carbon filter becomes saturated the display symbol C. Lights up and a signal sounds. Caution: As the filter becomes more and more saturated with grease, there is an increased risk of fire and the function of the extractor hood may be impaired. Important: Change the activated carbon filter promptly to prevent the risk of fire from the accumulation of heat when deep-fat frying or roasting. Filters and maintenance Inserting the filter: Warning: The halogen bulbs must be switched off and cool. 1. Remove the metal filters (see "Removing and inserting the metal grease filters"). 2. Insert the activated carbon filter. Fig. 4. 3. Raise the activated carbon filter in front and rotate the closures by 90°. Fig. 5. 4. Insert the metal grease filters (see Removing and inserting the metal grease filters). 5. Cancel the C in the display. . Switch the motor off (stop position). . Press for some seconds at the same time 0 and T push buttons. A signal sounds on the display and the display symbol C at the side goes out. Removing the filter: Warning: The halogen bulbs must be switched off and cool. 1. Remove the metal filters. 2. Rotate the closures by 90° and remove the activated carbon filter downwards. Fig. 5. 3. Insert the metal grease filters. Replacing the activated carbon filter: . During normal operation (1 to 2 hours per day) the activated carbon filters should be replaced approximately 1 x year. . A replacement filter can be obtained from any authorized dealer. . Use original f...