valutazioni - 0, GPA: 0
(
)
)
|
Facilità d'uso
The extractor hood can be used without restriction in circulating air mode – with an activated carbon filter. For exhaust air mode a one-way flap should be installed in the extractor hood unless already installed in the exhaust air pipe or wall box. If a one-way flap is not enclosed with the extractor hood, you purchase one from your dealer. If the exhaust air is conveyed through the outside wall, a telescopic wall box should be used. Before installation Optimum efficiency of the extractor hood: . Short, smooth exhaust pipe. . As few bends as possible. . Pipe diameter as large as possible (ideally 150 mm dia.) and wide pipe bends. If long, rough exhaust-air pipes, many pipe bends or smaller pipe diameters are used, the air extraction rate will no longer be at an optimum level and there will be an increase in noise. . Round pipes Short exhaust air pipe: inside diameter min. 120 mm, Longer exhaust air pipe: inside diameter min. 150 mm. . Flat ducts must have an inside cross-section equivalent to that of the round pipes. There should be no sharp bends. l120 mm dia. approx. 113 cm2 l150 mm dia. approx. 177 cm2 . If pipe diameters differ, insert sealing strip. . Ensure that there is an adequate air supply for exhaust air mode. Exhaust air directed backwards: Only possible inside tall wall cupboards depending on the size of the exhaust air pipe. . Make a hole in the rear panel of the wall cupboard, cutting out a notch for the power supply cable. Exhaust air directed upwards: 1. Make a hole in the top of the wall cupboard, cutting out a notch for the power supply cable. – template OI enclosed –. 2. If fitted, cut out the cupboard base to a min. depth of 270 mm over the entire width. Connecting a 150 mm exhaust pipe: . Attach the exhaust pipe directly to the air connector. Connection of 120 mm lexhaust air pipe: . Attach enclosed reducing connector to the air outlet. Holes in the air outlet must be sealed. . Attach exhaust air pipe to the reducing connector. Circulating-air mode . With activated carbon filter if exhaust-air mode is not possible. The complete installation set can be obtained from specialist outlets. The corresponding accessory numbers can be found at the end of these operating instructions. Preparing the wall cupboard This extractor hood is designed to be installed in a wall cupboard with the following dimensions: width: 600 mm depth: 293 to 350 mm height: min. 435 mm. If the cupboard is deeper than 293 mm, the extractor hood can be moved back, e.g. to put a spice rack in front of the extractor hood. To do this, place the template OII further back. Ensure that the cupboard is stable both during and after installation, even if fitted at the end of a row of kitchen units. 1. Mark two attachment points on both the right and left inside faces of the cupboard and make holes with a bradawl. When you drill: 2 mm diameter – max. 10 mm in depth. Use the enclosed template OII to mark the attachment points. 2. Screw on both attachment plates. 3. Attach the door to the cupboard and align. Observe the minimum distance between hotplates and extractor hood! Fig. 1. Switching over from exhaust air to circulating air mode Switching the electronic control system to circulating air mode: . The extractor hood has been set to exhaust air mode at the factory. . Before the mode can be changed, the extractor hood must have been connected and should be switched off. 1. Press and hold down the L button. 2. Press the button for approx. 3 seconds. . A ais displayed. 3. Release the buttons. . The display goes out shortly afterwards. Resetting to exhaust-air mode: 1. Repeat the procedure. . A #is displayed. 2. Release the buttons. . The display goes out shortly afterwards. 32 3. Tighten the two fixing screws with a screwdriver (cordless). 4. If required, shorten the wall cover to the required dimension (e.g. saw off). Attach the wall cover with the enclosed clips. Screw the wall cover to the wall cupboard. 5. Feed the mains connection cable out of the cupboard. 6. Connect the pipes in the wall cupboard. – If required, attach the air hose to the cupboard ceiling –. 7. Re-insert grease filter (see Operating instructions). Note: The extractor hood housing can be clad inside the wall cupboard (e.g. with chipboard). If so, observe the following: . The intermediate base must not be placed on the extractor hood housing. . Never attach cladding to the housing. . Provide access for customer service. Fitting into wall cupboard Check door alignment and readjust if necessary. 1. Remove grease filter (see Operating instructions). 2. Lift the extractor hood into the cupboard from below until both fixing lugs have locked firmly into position. . Align the extractor hood in the cupboard. . Carefully tighten both fastening screws. Check that the extractor hood is secure in the cupboard. 33 Fitting into wall cupboard . If the extractor hood is to be installed further back in the cupboard, the stops for the filter drawer can be moved ...
Questo manuale è adatto anche per i modelli :Cappe - DWFKB1D/02 (12.95 mb)
Cappe - DWFKB1E/01 (12.95 mb)
Cappe - DWFKB1E/02 (12.95 mb)
Cappe - DWFKB1E/03 (12.95 mb)