valutazioni - 0, GPA: 0
(
)
)
|
Facilità d'uso
2. Clean the filters. 3. Insert the clean filters back into the hood. 4. Clearing the # display. . Press the 0 button 2 x in succession. A signal sounds and the # display goes out. Activated carbon filter: For neutralizing odours in recirculating mode. Caution: As the filter becomes more and more saturated with grease, there is an increased risk of fire and the function of the extractor hood may be impaired. Important: Change the activated carbon filter promptly to prevent the risk of fire from the accumulation of heat when deep-fat frying or roasting. Saturation indicator: b When the activated carbon filter becomes saturated, the display symbol a lights up and a signal sounds. The signal is switched off when the fan is switched off. The activated carbon filter should be replaced straight away. Filters and maintenance Installation: Attention: The halogen bulbs must be switched off and must have cooled down. 1. Remove the metal filters (see "Removing and inserting the metal grease filters"). 2. Insert the activated-carbon filters. To do this, connect the filters to the pins on the sides of the fan. Removing the filter: Attention: The halogen bulbs must be switched off and must have cooled down. 1. Remove the metal filters. 2. Rotate the filters against the direction of the arrow and pull them out. 3. Insert the metal grease filters. Replacing the activated carbon filter: . During normal operation (1 to 2 hours per day) the activated carbon filters should be replaced approximately 1 x year. . A replacement filter can be obtained from any authorized dealer. . Use original filters only. By doing so you will obtain maximum performance from your extractor hood. Disposing of the old activated carbon filter: . There are no pollutants in the activated carbon filters. They can therefore be disposed of as part of your normal domestic refuse. 3. Rotate the filters in the direction of the arrow until they engage. If the filters have been installed correctly, they can no longer be removed. 4. Insert the metal grease filters (see "Removing and inserting the metal grease filters"). 5. Clearing the a display. . Press the 0 button 2 x in succession. A signal sounds and the C display goes out. Cleaning and care Isolate the extractor hood by pulling out the mains plug or switching off the fuse. Do not clean the extractor hood with abrasive sponges or with cleaning agents which contain sand, soda, acid or chlorine! . Clean the extractor hood with a hot soap solution or a mild window cleaner. . Do not scrape off dried-on dirt but wipe off with a damp cloth. . When cleaning the grease filters, remove grease deposits from accessible parts of the housing. This prevents the risk of fire and ensures that the extractor hood continues operating at maximum efficiency. . Note: Do not use alcohol (spirit) on plastic surfaces, as dull marks may appear. Caution: Ensure that the kitchen is adequately ventilated. Avoid naked flames! Clean the operating buttons with a mild soapy solution and a soft, damp cloth only. Do not use stainless-steel cleaner to clean the operating buttons. Stainless steel surfaces: . Use a mild non-abrasive stainless steel cleaner. . Clean the surface in the same direction as it has been ground and polished. . We recommend our stainless steel cleaner no. 461731. See enclosed service booklet for order address. Aluminium and plastic surfaces: . Do not use dry cloths. . Use a mild window cleaning agent. . Do not use aggressive, acidic or caustic cleaners. Observe the warranty regulations in the enclosed service booklet. Replacing the light bulbs 1. Switch off the extractor hood and pull out the mains plug or switch off the electricity supply at the fuse box. When switched on, the halogen bulbs become very hot. Even for some time after the bulbs have been switched off there is still a risk of burns. 2. Using a screwdriver, carefully remove the halogen bulb. Attention: If the halogen bulb is not removed properly, the appliance may be damaged. 3. Replace the halogen bulb (commercially available halogen bulb 12 V, max. 20 W, G4 bulb holder). Ensure that the contacts are in the correct position. Attention: Take hold of the halogen bulb with a clean cloth. 4. Plug the appliance into the mains or switch it on at the fuse box. Note: If the light does not function, check that the bulbs have been inserted correctly. Setting the saturation indicator If it becomes necessary to change the operating mode (exhaust-air/recirculating mode), the saturation indicator for the filters must also be altered (see Installation Instructions). If you encounter a problem If an # or a appears in the display: . See "Filters and maintenance" Section. If is not possible to operate the extractor hood: . Disconnect the extractor hood from the mains electricity supply by pulling out the plug or switching it off at the main fuse box. Wait for approx. 1 minute and then switch it on again. If you have any questions or if a fault occurs, please call Custom...
Questo manuale è adatto anche per i modelli :Cappe - I94K55N0/01 (878.14 kb)