valutazioni - 0, GPA: 0
(
)
)
|
Facilità d'uso
Use The hood uses rocker switches to activate the controls. The switch is on when the lower part of the button is depressed. The switch is off when the upper part of the button is depressed. Light Press the lower section of the button to turn lights on. Press the upper part of the button to turn the lights off. Fan Press the buttons up or down for the corresponding speed: Figure 1: Controls 1 2 3 Care and Cleaning WARNING: Be sure the entire hood (including the filters and light bulbs) has cooled and grease has solidified before attempting to clean any part of the appliance. DO NOT use the following! • Abrasive Pads such as those made from steel wool SOS.., Brillo.. or plastic mesh. • Abrasive cleaners such as Comet.., Ajax. and Zud... • Flammable products such as gasoline or kerosene. Hood Surface Painted Surfaces: For general care, wipe the outside of the hood with sudsy water or household cleaners such as Fantastic.. or Formula 409.., rinse well and dry with a clean soft cloth to avoid water marks. Stainless Steel Surfaces: Wipe and dry stainless steel in the same direction as the grain. Avoid using too much pressure, which may mar the surface. To remove finger prints and give added shine, use cleaners such as Stainless Steel Magic... Do not allow any cleaning compounds to remain in contact with stainless steel for extended periods. English 2 English 3 Filters The hood has removable aluminum filters that must be cleaned when they collect grease. The filters can be cleaned with soap and water or in the dishwasher. When used over a wok or other high grease application, more frequent cleaning may be required. Remove the filters for cleaning: push the handle in and pull down. The front will come out first. Then pull the back down and out. See Figure 2. Figure 2: Filters To replace the filters: insert the back ends first, then while holding the handles, push in and up until the filters are secured in place. Buttons Wipe with sudsy water or household cleaners such as Fantastic(r) or Formula 409(r), rinse well and dry with a clean soft cloth to avoid water marks. Maintenance Lights Use a 40W, 120V E12bulb (chandelier style). NOTE: Turn off the lights and fan and allow lights to cool before handling. If lights do not operate upon installation, check for proper insertion. Light bulbs can be cleaned with soap and water. CAUTION: TURN POWER OFF AT BREAKER BEFORE REMOVING A DAMAGED BULB. DO NOT TOUCH THE BULBS IMMEDIATELY AFTER USE. THE BULBS WILL REMAIN HOT FOR SEVERAL MINUTES. Light Bulb Replacement Place fingers behind lens and push out from behind. Figure 3: Light Bulb Replacement Remove the damaged light bulb and replace. Snap lens back into place. Do not use cooktop while hood is disassembled, to ensure adequate ventilation. Troubleshooting Before calling service, check the possible explanations below. If these solutions fail, call service. Please have your serial number and model number ready. They are located on the underside of the hood on the left side. Table 1: Troubleshooting Problem Possible Explanations Noise During Operation Some noise is normal due to vibration and air movement. Excessive noise indicates one of the following: •Ductwork is too small/undersized. •Ductwork is too large/oversized. •Ductwork is loose. •Transition is too small or too loose. •Screws in trim parts, etc. are loose. Noise When Not Operating Backflow flap on outside of duct wall cap moves with the wind. Fan Motor Does Not Work • Power supply to hood is not sufficient. •Wires are not completely connected. Lights Under Hood Hum A slight hum is normal. Operation of Hood Trips Breaker •Wiring is not correct. •Circuit is not correct. English 4 Warranty The warranties provided by BSH Home Appliances Corp. in this Statement of Limited Warranty apply only to the BSH Ventilation Hood (“hood”) and Internal Blower sold to you, the first using purchaser, provided that the hood and blower were purchased (1) for your use and not for resale and (2) in the United States or Canada and is located in the country of purchase. As used in this Statement of Limited Warranty, the term “Date of Installation” shall refer to the earlier of the date the hood and internal blower are installed or ten (10) business days after the date the hood and internal blower are sold to the first using purchaser, the warranties stated herein apply only to the first using purchaser and are not transferable. Standard Limited Warranty BSH warrants that its hood and internal blower are free from defects in materials and workmanship for a period of twelve (12) months from the Date of Installation. During the warranty period, BSH or its authorized service center will repair or replace, at its sole option, any hood or internal blower that proves to have been defective under conditions of normal use without charge. All removed parts and components shall become the property of BSH, at BSH’s option. All replaced and/or repaired parts shall assume the identity of the original part...
Questo manuale è adatto anche per i modelli :Cappe - LC479650UC/01 (764 kb)
Cappe - LC479650UC/02 (764 kb)