valutazioni - 3, GPA: 3.7 ( )

Produttore : Amana File Size : 365.17 kb File Nome : 347721EN.pdf Lingua di insegnamento:

If these clearances cannot be maintained a heat insulating pad is required between the cooker and the refrigeration appliance. If the refrigeration appliance is installed next to another refrigerator or free zer a clearance of 5 cm at the sides is required, in order to prevent the formation of condensation on the outside of the appliance. Your appliance needs air For safety reasons, minimum ventilationmust be as shown Fig. Attention: keep ventilation openings clear of obstruction; Fitting the Door Handles 1. Screw the top handle bracket to the handle rod (1). Fit the bottom handle bracket on the lower left- hand side of the door (2). 2. Fit the top handle bracket on the top left-hand side of the door (3) and screw the handle rod to the bottom handle bracket (4). Attention! Do not overtighten the screws (max. 2 Nm) as you may damage the door handles. Rear spacers Fit the rear spacers contained in the appliance to ensure even dissipation of heat genereted during operation. Proceed in the sequence illustrated by the figures. Rehingeing the door The side at which the door opens can be changed from the right side (factory adjustment) to the left side, if the installation site requires. Warning! When changing the side at which the door opens, the appliance may not be connected to the mains. Remove plug from the mains beforehand. Procced as follow: 1. Remove the clip-in ventilation grille (D). 2. Remove the bottom hinge (E) by unscrewing the fixing screws. 3. Slide the bottom door off the centre hinge (H). 4. Remove the centre hinge and slide the top door off pin (G); unscrew pin (G) and refit it on the opposite side. 5. Remove the two plugs, to reveal the holes for the hinge pivots, and remount them on the other side. 6. Refit the top door and the centre hinge (H) on the opposite side. 7. Refit the bottom door. 8. Using a 10 mm spanner, unscrew the hinge pin (E) and reassemble it on the opposite side of the hinge; 9. Refit bottom hinge (E) on the opposite side, using the screws previously removed. 10. Remove blanking cover (F) from ventilation grille (D) by pushing it in the direction of the arrow and refit it on the opposite side. 11. Refit ventilation grille (D), clipping it into place. Unscrew the top handle bracket from the handle rod (1). Unscrew the bottom handle bracket from the door (2). Unscrew the top handle bracket from the door (3) and screw onto the bottom right- hand side of the door (4). Turn the handle bracket with the handle rod 180° and screw them to the door (5) and the fitted handle bracket (6). Move the small plug from right to left. In any case you do not want to carry out the above mentioned operations, contact the nearest After Sales Service Force.. The After Sales Service specialist will carry out the reversibility of the doors at your cost. Attention: After having reversed the opening direction of the doors check that all the screws are properly tightened and that the magnetic seal adheres to the cabinet. If the ambient temperature is cold (i.e. in Winter), the gasket may not fit perfectly to the cabinet. in that case, wait for the natural fitting of the gasket or accelerate this process by heating up the part involved with a normal hair- drier. Electrical connection Before initial start-up, refer to the appliance rating plate to ascertain if supply voltage and current values correspond with those of the mains at the installation location. e.g.: AC 230 ... 240 V 50 Hz or 230 ... 240 V~ 50 Hz (i.e. 230 to 240 volts alternating current, 50 Hertz) The rating plate is inside the appliance on the left. A correctly installed, earthed socket is required for the electrical supply. The supply must have a fuse rating of at least 10 Amps. If the socket is not accessible once the appliance is built in, the electrical installation must include suitable means of isolating the appliance from the mains (e.g. fuse, cut-out, current trip or similar with a minimum contact separation of 3 mm). Attention: The mains connection cable may only be replaced by a skilled electrician. Please contact your dealer or our customer service department for repairs. Prior to Initial Start–Up • Please clean the appliance interior and all accessories prior to initial startup (see section: “Cleaning and Care”). Operating and indicator panel Fridge . . . A. Fridge button ON/OFF B. Temperature setting button (for warmer temperatures) C. Temperature display D. Temperature setting button (for colder temperatures) E. COOLMATIC function "on" indicator (yellow) F COOLMATIC button Temperature setting buttons The temperature is adjusted using the „B“ and „D“ buttons. These buttons are connected to the temperature display. • The temperature display is switched over from the display of the ACTUAL temperature (Temperature display is illuminated) to the display of the DESIRED temperature (Temperature display flashes) by pressing one of the two buttons, „B“ or „D“ . • Each time one of the two buttons is pressed again the DESIRED temperat...

Scarica la tua

Per scaricare, digitare 2 cifre :