valutazioni - 4, GPA: 3.8
(
)
)
|
Facilità d'uso
Do not remove the door/drawer if it is not needed. Before removing the door/drawer make sure you read following items. Disconnect power to the Refrigerator before removing the door or drawer. WARNING • Be careful not to drop, damage or scratch the door/drawer while removing them. • Be careful not to get injured while removing the door/drawer. • Reattach the door/drawer properly to avoid: -Moisture from air leakage. -Uneven door alignment. -Wasting energy due to improper door seal. 14_ 14_14_setting up setting upsetting up setting up _15 01 setting up setting up your refrigerator Disassembling the fridge door Be careful not to drop and scratch the fridge door while removing the fridge door! 1. Remove the 3 screws holding down the top table and remove it. 2. Disconnect electric wire on the top of the refrigerator. 3. Remove the 3 hex bolts that hold the hinge on the top of the refrigerator with the 10mm socket wrench. 4. Remove the screw that holds the ground wire with a philips screwdriver(+). 5. Separate the hinge from the electric wire and ground wire as shown above. 6. Lift the door straight up to remove. Be careful not to drop and scratch the doors while removing them. Disassembling the freezer door (DRAWER TYPE) 1. Separate the cap on the middle hinge. 2. Remove the screw attached to the left and right middle hinges with a philips screwdriver(+). Remove the 2 hex head bolts attached to the left and right middle hinges with an allen wrench(O5mm). WARNING Top Table Socket wrench Middle Hinge 16_ setting up 3. After opening the Freezer door, lift the drawer box. 4. Remove 4 hex head bolts from both sides with a socket wrench(10mm) 5. Lift up the freezer door from the rails. Be careful not to drop and scratch the freezer door. Disassembling the freezer door (swing type) 1. Separate the Cap on the Middle Hinge. 2. Remove the screw attached to the left and right middle hinges with a philips screwdriver(+). Remove the 2 hex head bolts attached to the left and right middle hinges with an allen wrench(O5mm). 3. Remove the Middle Hinge connected to the Freezer. 4. Lift up the freezer door from the hinge. Be careful not to drop and scratch the freezer door. Middle Hinge setting up _17 01 setting up setting up your refrigerator reassembling the fridge door 1. Insert and tighten the screw into the left and right middle hinges with a philips screwdriver(+). 2. Insert and tighten the 2 hex head bolts into the left and right middle hinges with an allen wrench(O5mm). 3. Replace the middle hinge cap. 4. Place the hole in the bottom of the left door over the middle hinge. 5. Insert the left upper hinge shaft into the hole on the corner of the fridge door. 6. Insert the upper hinges into the holes at the top of the door. Insert and tighten the 3 hex head bolts into the left and right upper hinges with a socket wrench(10mm). 7. Insert and tighten the ground screw into the left and right upper hinges with a philips screwdriver(+). 8. Connect the electronic wire on the top of the refrigerator. 9. Position the top table in place. Insert and tighten the 3 screws into the top table with a philips screwdriver(+). 18_ setting up Reassembling the freezer door (DRAWER TYPE) 1. Pull out the rails to the full length on each sidle of the cabinet evenly. 2. Hang the freezer door front onto open slot on the sides. 3. With the 10mm wrench, reattach 4 bolts to connect the rail with the door. 4. Replace the drawer box. Reassembling the freezer door (SWING TYPE) 1. Place the hole in the bottom of the freezer door over the right side low hinge. 2. Replace the middle hinge connected to the freezer. 3. Insert and tighten the screw into the left and right middle hinges with a philips screwdriver(+). Insert and tighten the 2 hex head bolts into the left and right middle hinges with an allen wrench(O5mm). 4. Replace the cap on the middle hinge. Slot setting up _19 01 setting up setting up your refrigerator How to reverse the door (OPTION) Unplug the refrigerator or disconnect the power. 1. Remove 3 screws on the hinge cover. 2. Disassemble the hinge cover. 3. Disassemble 2 connectors. (a housing and a reed switch) 4. Disassemble ground wire by removing 1 screw on each side. 5. Disassemble the upper hinge by removing 3 bolts on each side with the 10mm wrench. 1. Avoid the wire damage. 2. Fridge door is possible to tip over at this time. 6. Remove each fridge doors by lifting it up. 1. Possible to drop or scratch the door at this time. 2. Middle hinge cap may come off with the door. 7. Disassemble middle hinge cap. 8. Remove 1 screw and 2 bolts of each side (use O5mm allen wrench). 1. At first, Remove left side middle hinge and right side. 2. Be careful not to drop the freezer door. 9. Remove the freezer door by lifting it up. 1. Possible to drop or scratch the door at this time. 2. Low hinge cap may come off with the door. 10. Remove 2 screws. 11. Separate front leg Cover. Cap Cover 20_ setting up 12. Separate the Cap of the front leg Cover. (pull ...
Questo manuale è adatto anche per i modelli :Frigoriferi - RF62HEPN (7.2 mb)
Frigoriferi - RF62NEPN (7.2 mb)
Frigoriferi - RF62NERS (7.2 mb)
Frigoriferi - RF62WBPN (7.2 mb)