valutazioni - 1, GPA: 3
(
)
)
|
Facilità d'uso
See instruction below: 10 642 97531 Pin Pin Assignment (HD AUDIO) Pin Pin Assignment (AC’97 AUDIO) 1 MIC2 L 1 MIC In 2 AGND 2 GND 3 MIC2 R 3 MIC Power 4 AVCC 4 NC 5 FRO-R 5 Line Out (R) 6 MIC2_JD 6 Line Out (R) 7 F_IO_SEN 7 NC 8 Key (no pin) 8 Key (no pin) 9 FRO-L 9 Line Out (L) 10 LINE2_JD 10 Line Out (L) Locate the internal audio connectors from your motherboard or sound card. Consult your motherboard or sound card manual for the pin-out positions. 3.5” Device Installation With the front bezel facing you, swing the front door out. It can swing 270. so the door will parallel with the side of the case. You can see there are four 5.25” and one 3.5” external drive bays. Inside the case there are two 3.5” drive cages, which can house up to six hard drives. Note: We recommend using the lower HDD cage to get the maximum possible cooling and quiet computing. The Upper HDD Installation 1. Remove the thumbscrew holding the upper HDD cage. 2. Pull the HDD cage from its position by pulling the ring towards you. 3. There are two HDD trays inside the cage. Squeeze the metal clips on each side of the tray and slide the tray out. 4. Mount your hard drive into the drive tray with the special screws provided. Don’t over-tighten the screws as this will reduce the vibration and noise 4 dampening ability of the silicone grommets. Note: Always mount the HDD with the thicker side of the silicone grommets facing up. 5. Slide and lock the tray back into the cage. 6. Slide the cage back to the case and fasten the thumbscrew. 7. Find the right Molex or SATA connector on the power supply and connect it to the hard drive. 8. Repeat the same procedure for the other drives. The Lower HDD Installation 1. Remove the thumbscrew holding the lower HDD cage. 2. Pull the HDD cage from its position by pulling the ring towards you. 3. You can mount four hard drives inside the cage. They are mounted vertically with the silicone grommets sitting at both sides. 4. Mount your hard drive into the drive cage with the special screws provided. Don’t over-tighten the screws as this will reduce the vibration and noise dampening ability of the silicone grommets. Note: Always mount the HDD with the thicker side of the silicone grommets facing up. 5. Slide the cage back into the case and fasten the thumbscrew. 6. Find a Molex or SATA connector on the power supply and connect it to the hard drive. 7. Repeat the same procedure for the other drives. External 3.5” Drive Installation There is one external 3.5” drive bay. 1. Carefully remove the plastic drive bay cover and metal plate covering the drive bay. 2. Find a pair of 3.5”drive rails in the box containing the top fan spoiler. 3. Mount the drive rails onto the sides of the 3.5” device. Make sure the metal portion is angled on the outside and facing forward. 4. Slide the device into the drive bay until it clicks into place. 5. Connect a small 4-pin connector from the power supply to the 4-pin connector on the floppy drive. 5.25” Device Installation There are four 5.25” drive bays that need a total of 8 drive rails. 1. Carefully remove the plastic drive bay cover and the metal plate covering the drive bay. 2. Mount the drive rails onto the sides of the 5.25” device. Make sure the metal portion is angled on the outside towards the outside of the case. 3. Slide the device into the drive bay until it clicks into place. 4. Mount the other devices accordingly. 5. Connect a 4-pin Molex connector from the power supply to the 4-pin connector on each of the devices. Cooling System The TriCool™ fan: The case includes three installed 120mm TriCool™ fans. The three-speed fans let you choose between quiet performance or maximum cooling (see specifications below). Note: The minimum voltage to start the fan is 5V. We recommend our users to set the fan speed to High if you choose to connect the fan to a fan control device or to the Fan-Only connector found on some Antec power supplies. 5 A fan-controller regulates the fan speed by varying the voltage to it. The voltage may start as low as 4.5V to 5V. Connecting a TriCool™ set on Medium or Low to a fan-control device may result in the fan not being able to start. The already lowered voltage from the fan controller will be further reduced by the TriCool™ circuitry below 5V. The Top and Rear Exhaust TriCool™ Fans External fan switches allow adjusting the speed of these two fans without having to open the case. Note: We recommend that our users set these two fans to Low in order to cool the CPU more effectively. The two fans are mounted so that the air is blowing out of the case. The top fan comes with a spoiler to mount on the top of the case. To install the spoiler: 1. With the higher end of the spoiler facing the rear of the case, carefully align the tabs of the spoiler with the notches on the case. 2. Insert the tabs to the notches and slide the spoiler towards the front of the case until it clicks into position. The Lower Chamber TriCool™ Fan This is a standard 120mm fan. ...
Questo manuale è adatto anche per i modelli :Frigoriferi - P180 (1.02 mb)
Frigoriferi - P182SE (1.02 mb)
Alimentazione e alimentazione - P182 SE (1.02 mb)