valutazioni - 2, GPA: 4.5 ( )

Produttore : Avanti File Size : 843.68 kb File Nome : 345017EN.pdf Lingua di insegnamento:

Water flows into the re-The water outlet is clogged. Clean the water outlet. frigerator. Products prevent that water Make sure that products do not flows into the water collector. touch the rear plate. Water flows on the The melting water outlet does Attach the melting water outlet ground. not flow in the evaporative tray to the evaporative tray. above the compressor. 20 20 What to do if… Problem Possible cause Solution The temperature in the The temperature regulator is not Set a higher temperature. appliance is too low. set correctly. The temperature in the The temperature regulator is not Set a lower temperature. appliance is too high. set correctly. The temperature in the refrigerator is too high. The door is not closed correctly. The product temperature is too high. Many products are stored at the same time. There is no cold air circulation in the appliance. Refer to "Closing the door". Let the product temperature decrease to room temperature before storage. Store less products at the same time. Make sure that there is cold air circulation in the appliance. The temperature in the Products are too near to each Store products so that there is freezer is too high. other. cold air circulation. Technical problems electrical malfunction Contact Customer Service Department Upper or lower square is An error has occurred in meas-Call your service representative shown in the temperature uring the temperature (the cooling system will continue Display. to keep food products cold, but temperature adjustment will not be possible). dEMo appears on the Dis-The appliance is in demonstra-Keep pressed approximately 10 play. tion mode (dEMo) . sec. the OK button since a long sound of buzzer is heard and the Display shut off for a short while: appliance start works regularly. Replacing the lamp CAUTION! Disconnect the plug from the mains socket. 1. Press on the rear hook of the lamp cover by a screwdriver and at the same time pull and rotate the cover in the direction of the arrow. 2. Replace the lamp with one of the same power and specifically designed for household appliances. (the maximum power is shown on the light bulb cover). 12 3. Install the lamp cover by fixing it into its original position. 4. Connect the plug to the mains socket. 5. Open the door. Make sure that the light comes on. Technical data 21 Closing the door 1. Clean the door gaskets. 2. If necessary, adjust the door. Refer to "Installation". 3. If necessary, replace the defective door gaskets. Contact the Service Center. TECHNICAL DATA Dimension of the recess Width 695 mm Depth 696 mm Rising Time 20 h Voltage 230-240 V Frequency 50 Hz Height 1950 mm The technical information are situated in the rating plate on the internal left side of the appliance and in the energy label. INSTALLATION WARNING! Read the "Safety Information" carefully for your safety and correct operation of the appliance before installing the appliance. Positioning Install this appliance at a location where the ambient temperature corresponds to the climate class indicated on the rating plate of the appliance: Climate class Ambient temperature SN +10°C to + 32°C N +16°C to + 32°C ST +16°C to + 38°C T +16°C to + 43°C 22 22 Installation Location The appliance should be installed well away from sources of heat such as radiators, boilers, direct sunlight etc. Ensure that air can circulate freely around the back of the cabinet.To ensure best performance, if the appliance is positioned below an overhanging wall unit, the minimum distance between the top of the cabinet and the wall unit must be at least 100 mm . Ideally, however, the appliance should not be positioned below overhanging wall units. Accurate levelling is ensured by one or more adjustable feet at the base of the cabinet. If the cabinet is placed in a corner and the side with the hinges facing the wall, the distance between the wall and the cabinet must be at least 10 mm to allow the door to open enough so that the shelves can be removed. WARNING! It must be possible to disconnect the appliance from the mains power supply; the plug must therefore be easily accessible after installation. Electrical Connection CAUTION! Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person. WARNING! This appliance must be earthed. The manufacturer declines any liability should these safety measures not be observed. 15mm15mm100mm The wires in the mains lead are coloured in accordance with the following code: Installation 23 135 Green and Yellow: Earth Brown: Live Blue: Neutral As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: 1. Connect the wire coloured green and yellow to the terminal marked either with the letter “E“ or by the earth symbol or coloured green and yellow. 2. Connect the wire coloured blue to the terminal either marked with the letter “N“ or colour...

Scarica la tua

Per scaricare, digitare 2 cifre :