valutazioni - 3, GPA: 3
(
)
)
|
Facilità d'uso
The proper vehicle electrical system connections should follow this procedure. 2. DO NOT connect the charger to any electrical system without providing proper fusing, A 10 Amp fuse must be connected in the positive ( + ) supply lead to the charger. Under no circumstances shall the charger be fused greater than 10 Amps. The fuse should be located close,to. the point, of connection to the vehicle electrical system. Black & Decker Number 131423 includes a fuse holder and lead wire assembly for this purpose and may be purchased at Black & Decker Service Centers, 3. Any external wiring to the charger cordset should be 18 gauge or larger. 4. The two conductors of'the charger cordset may be separated. The ribbed conductor is the negative (—) input, and the smooth conductor is the positive (+) input SMOOTH CONDUCTOR (4) CHARGER INPUT CORDSET RIBBED CONDUCTOR (-) 5. The ribbed conductor is connected; via an appropriate connector or wiring terminal to a negative (—) terminal of the electrical system. In negative ground systems, the vehicle chassis is a convenient connection point, provided any surface corrosion or paint is first removed from the connection area. BSD FUSEHOLDER" 131423 (+) POSITIVE TERMINAL OF ELECTRICAL SYSTEM ( FUSE BLOCK ) CHARGER ’ CORDSET RIBBED LEAD NEGATIVE TERMINAL (CHASSIS) 6. The smooth conductor is connected to one lead of a fuse-holder containing a 10 Amp fuse; the electrical connection should be secured by twisting the conductors of the two leads, soldering or wire-nutting, and placing electrical grade tape over the joint to prevent short circuits. The remaining fuse-holder lead is connected via an appropriate connector or wiring terminal to a positive (-f) terminal of the vehicle fuse block. (Continued on next page) BSD FUSEHOLDER#131423 (+) POSITIVE TERMINAL OF ELECTRICAL SYSTEM ( FUSE BLOCK) NEGATIVE TERMINAL (CHASSIS) 7. If an extension to the existing cordset is made, care must be taken to insure like polarities of the extension cable and the charger cordset are connected together. All wiring joints should be secure and adequately insulated with electrical grade tape to prevent exposed wire from producing short circuits. Use 18 gauge or larger conductors for cordset extension wiring. 8. WARNING: Wiring to the charger cordset and electrical system connections should be routed to avoid sharp edges, doors, crushing loads, and corrosives which may damage the wiring and create a hazard. 9. WARNING; Connections to the vehicle electrical system should be made only at the vehicle fuse block. Failure to properly fuse and splice wire terminations can result in severe damage to the vehicle electrical system and create a fire hazard, . ■ ■ . STORAGE RECOMMENDATIONS l. The best storage place is one that is cool and dry-and excess heat or cold. -away from direct sunlight 2. Long storage- will not-.harm' the Energy Pak or charger. Under proper conditions, they;.'can be stored for 5 years or more, 3. The charger may remain connected to the vehicle (through either the cigarette lighter socket or hard wired per special installation instructions) indefi- . nitely. There is no drain on the vehicle battery, except when charging an . Energy Pak. COMMERCIAL/INDUSTRIAL USE WARRANTY Black & Decker warrants this product for one year from the date of purchase. We will repair without charge, any defects due to faulty material or workmanship. Please return the complete unit, transportation prepaid, to any Black & Decker Service Center or Authorized Service Station listed under “Tools-Electric” in the yellow pages. SERVICE In the event service is required, take or send the unit, complete with charger, to your nearest B&D Service Center. The address may be found under “Tools-Electric” in the yellow pages of your telephone directory. IMPORTANT To assure product SAFETY and RELIABILITY: Repairs, maintenance, and adjustments should be performed by BLACK & DECKER Service Centers or other qualified service organizations, always using BLACK & DECKER replacement parts. BLACK & DECKER (U.S.) INC., TOWSON, MARYLAND 21204, U.S.A. Form No. 724308 (July79-PS) Printed in U.S.A. b d\ Black & Decker. INSTRUCTIONS FOR N0. 98002 12 VOLT FAST CHARGER For Use with No. 98003 or 91-009 Energy Pak BUTTON ■INDICATOR LIGHT LIGHTER PLUG- Black & Decker, and ^£2? are registered trademarks of The Black and Decker Manufacturing Company, Towson, Maryland, U.S.A. You can use your B&D 98002 12 Volt Fast Charger in any vehicle having a cigarette lighter socket operating from a 12 volt negative ground battery. Some vehicles have a 12 volt positive ground battery. For these vehicles, the charger must be converted for use with a positive ground system. This modification may be performed following the simple instructions in this manual, or by returning the unit to any B&D Service Center. See “Tools, Electric" in the Yellow Pages for your nearest B&D Service Center. Charging time for a completely discharge...
Questo manuale è adatto anche per i modelli :Caricabatterie - 98002 (2.01 mb)