valutazioni - 0, GPA: 0
(
)
)
|
Facilità d'uso
This section describes a simple network consisting solely of a wireless LAN access point (bridge) connected to an computer via a LAN cable or wireless, with no connections to other networks or devices. Follow the steps below to use the WT-4 in this type of network. 1: Get Ready 2: Assign the Computer an IP Address 3: Using Windows Firewall 4: Configure the Wireless LAN Access Point 5: Configure the Computer for Wireless Access 6: Copy the Network Profile to the Camera 7: Connect to the Computer To the top of the page Equipment Ready the following: • A WT-4 wireless transmitter • A fully-charged EN-EL3e battery for the WT-4 • A digital SLR camera that supports the WT-4 (the illustrations show a Nikon D3) • A fully-charged battery for the camera file:///C:/Users/harpley/Desktop/Windows7_html/02_7PI_En.html 05/12/2011 Configuring the WT-4 for Upload to a Computer (Infrastructure Mode) Page 2 of 25 • A computer with Windows 7 Ultimate/Professional/Home Premium/Home Basic/Enterprise edition and a compatible version of the WT-4 Setup Utility installed • A wireless LAN access point • A LAN cable •A memory card • A USB cable • Manuals for the above equipment Network Settings Note the IP addresses, encryption, and other settings that will be used in the wireless LAN. The following are intended as examples only. • IP address for the WT-4: 192.168.1.4 • IP address for the computer: 192.168.1.3 • IP address of the wireless LAN access point: 192.168.1.2 • Subnet mask: 255.255.255.0 • Network name (SSID): WT-4 • Communication mode: Infrastructure • Authentication: WPA-PSK • Encryption: TKIP • Encryption key: abcde123 To the top of the page Choose an address for the computer. The following IP address is intended as an example only. • IP address: 192.168.1.3 • Subnet mask: 255.255.255.0 2–1 Open the Network and Internet > Network and Sharing Center control panel. file:///C:/Users/harpley/Desktop/Windows7_html/02_7PI_En.html 05/12/2011 Configuring the WT-4 for Upload to a Computer (Infrastructure Mode) Page 3 of 25 2–2 Select Change adapter settings. 2–3 Right-click the network icon (Wireless Network Connection if the access point and computer are connected via a wireless network, Local Area Connection if the access point is connected by a LAN cable) and select Properties from the menu that appears. file:///C:/Users/harpley/Desktop/Windows7_html/02_7PI_En.html 05/12/2011 Configuring the WT-4 for Upload to a Computer (Infrastructure Mode) Page 4 of 25 2–4 Select Internet Protocol Version 4 (TCP/IPv4) and click Properties. 2–5 Select Use the following IP address and enter the IP address and subnet mask for the computer. Click OK to exit and then click Close to close the properties dialog. This completes the process of assigning an IP address to the computer. file:///C:/Users/harpley/Desktop/Windows7_html/02_7PI_En.html 05/12/2011 Configuring the WT-4 for Upload to a Computer (Infrastructure Mode) Page 5 of 25 5 To the top of the page Windows Firewall is enabled by default in Windows 7. If you are using Windows Firewall, turn all other firewalls off and allow access to the following ports, which are used for wireless connections: • TCP: port 15740 • UDP: port 5353 3–1 Go to the System and Security > Windows Firewall control panel. file:///C:/Users/harpley/Desktop/Windows7_html/02_7PI_En.html 05/12/2011 Configuring the WT-4 for Upload to a Computer (Infrastructure Mode) Page 6 of 25 3–2 Click Turn Windows Firewall on or off. 3–3 If Windows Firewall is on, deselect Block all incoming connections, including those in the list of allowed programs and click OK. file:///C:/Users/harpley/Desktop/Windows7_html/02_7PI_En.html 05/12/2011 Configuring the WT-4 for Upload to a Computer (Infrastructure Mode) Page 7 of 25 5 Network Type The network type (private or public) can be viewed in the Network and Internet > Network and Sharing Center control panel. 3–4 Select Advanced settings. file:///C:/Users/harpley/Desktop/Windows7_html/02_7PI_En.html 05/12/2011 Configuring the WT-4 for Upload to a Computer (Infrastructure Mode) Page 8 of 25 5 3–5 In the “Windows Firewall with Advanced Security” window, select Inbound Rules and click New Rule… in the Actions panel. 3–6 The “New Inbound Rule Wizard” will be displayed. Select Port and click Next. file:///C:/Users/harpley/Desktop/Windows7_html/02_7PI_En.html 05/12/2011 Configuring the WT-4 for Upload to a Computer (Infrastructure Mode) Page 9 of 25 5 3–7 Select TCP, and then select Specific local ports and enter 15740. Confirm that the port numbers are correct and click Next. 3–8 Confirm that Allow the connection is selected and click Next. file:///C:/Users/harpley/Desktop/Windows7_html/02_7PI_En.html 05/12/2011 Configuring the WT-4 for Upload to a Computer (Infrastructure Mode) Page 10 of 25 3–9 Choose the type of network to which the rule applies and click Next. The network type can be viewed in the Network and Internet > Network and Sharing Center control panel; if you are unsure, select all thre...