• The charger is designed to operate on standard household electrical power (120 Volts). Do not attempt to use it on any other voltage. This does not apply to the vehicular charger. Charging Procedure 1. Plug the charger into an appropriate outlet. 2. Insert the battery pack into the charger. Be sure the pack is fully seated in the charger. The red (charging) light will blink continuously indicating that the charging process has started. 3. The completion of charge will be indicated by the red l

If either of these is the desired angle, retighten the lever (J) by lowering it. If you desire another angle, continue tilting the shoe until the pointer aligns with the desired mark. Retighten lever (J) by lowering it. Shoe Adjustment for 90° Cuts WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect tool from battery pack before making any adjustments or removing/installing attachments or accessories. IF ADDITIONAL ADJUSTMENT IS NEEDED (FIG. 12) 1. Adjust the saw

4. Select the proper blade for the application (see Blades). Always use blades that are the correct size (diameter) with the proper size and shape center hole for mounting on the saw spindle. Always assure that the maximum recommended speed (rpm) on the saw blade meets or exceeds the speed (rpm) of the saw. 5. Follow steps 2 through 6 under To Install the Blade, making sure that the blade will rotate in the proper direction. DC310 ONLY (FIG. 6, 7) To Install the Blade: 1. Place inner clamp washe

2 YEARS FREE SERVICE ON XRP ™ BATTERY PACKS DC9096, DC9091 and DC9071 90 DAY MONEY BACK GUARANTEE If you are not completely satisfied with the performance of your DEWALT Power Tool, Laser, or Nailer for any reason, you can return it within 90 days from the date of purchase with a receipt for a full refund – no questions asked. 9 FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing, call 1-for a free replacement. SAVE THESE INSTRUCTIONS FOR FUTURE USE English Fra

2. The charger and battery pack may become warm to touch while charging. This is a normal condition, and does not indicate a problem. 3. If the battery pack does not charge properly — (1) Check power at receptacle by plugging in a lamp or other appliance. (2) Check to see if receptacle is connected to a light switch which turns power off when you turn out the lights. (3) Move charger and battery pack to a location where the surrounding air temperature is approximately 65°F - 75°F (18°- 24°C). (4

CAUTION: When sawing into walls, floors or wherever “live” electrical wires may be encountered, DO NOT TOUCH ANY FRONT METAL PARTS OF THE TOOL! Hold the tool FIG. 6 English English FIG. 7 FIG. 8 only by the plastic or rubber handle and housing to prevent electric shock if you saw into a “live” wire. Metal Cutting (Fig. 7) This unit has different metal cutting capacities depending upon type of blade used and the metal to be cut. Use a finer blade for ferrous metals and a coarse blade for non-ferr

Always use correct battery pack (pack supplied with tool or replacement pack exactly like it.) Never install any other battery pack. It will ruin your tool and may create a hazardous condition. 5 English English Fan Cooling This charger is equipped with an internal of DEWALT DW0242 battery packs. The fan operation is automatic and will turn on when required during battery also cycle periodically when there is no battery to blow dust from the fan vents. WARNING: Fan may blow debris from vent area

The charger will cycle through the following modes. 1. The red light will blink continuously indicating that the 1-hour charge cycle has started. 2. When the 1-hour charge cycle is complete, the light will stay on continuously and will no longer blink. This indicates that the pack is fully charged and can be used at this time. 3. Whenever the pack is left in the charger after the initial 1-hour charge, the charger will begin the Automatic Tune-Up™ Mode. This mode continues up to 8 hours or until

3. The completion of charge will be indicated by the red light remaining ON continuously. The pack is fully charged and may be used at this time or left in the charger. WARNING: Don't allow any liquid to get inside charger. Electric shock may result. To facilitate the cooling of the battery pack after use, avoid placing the charger or battery pack in a warm environment such as in a metal shed, or an uninsulated trailer. 3 English English CAUTION: Neverattempt to open the battery pack for any rea

• Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged cords immediately. Damaged cords increase the risk of electric shock. • When operating a power tool outside, use an outdoor extension cord marked “W-A” or “W.” These cords are rated for outdoor use and reduce the risk of electric shock. Recommended Minimum Wire Size for Extension Cords Total Length of Cord 25 ft. 50 ft. 75 ft.