valutazioni - 3, GPA: 4.3
(
)
)
|
Facilità d'uso
Attach left sideburner shelf using three 1/4-20x3/4” screws, 7mm lock washers, 7mm flat washers, 1/4” nuts, shown A. Attach rear of shelf using one 1/4-20x1.” screw, 7mm lock washer, and 7mm flat washer in lower hole, shown B. Attach front of shelf and fascia using one #8x3/8” self-tapping screw and large flat washer, shown C. Under main control panel, attach front of shelf and fascia using one 1/4-20x3/4” screw, 7mm lock washer, 7mm flat washer and 1/4” nut, shown D/E. Now you may fully tighten lower screws on upper back panel. 1/4-20x3/4” screw Back of main control panel Control panel Fascia, left sideburner shelf Left sideburner shelf Flangeinto Brackets Bracket 1/4-20x3/4” screw screw washer 7mm flat #8x3/8” self-tappinglarge flatwasher 7mm lock 7mm flat 1/4”nut ABC screw 1/4-20x1.” washer 7mm lockwasher ED1/4”nut 7mm lockwasher 7mm flat washer 8 88 First, remove the two screws and lock washers factory attached to the sideburner valve bracket. Position sideburner valve bracket beneath sideburner shelf fascia so that valve stem comes through larger center hole in fascia. Align the holes on valve bracket with left and right holes on fascia. Secure using lock washers and screws that were removed from bracket. Next, place sideburner bezel over valve stem on front side of fascia. Align small holes on bezel with upper and lower holes on fascia. Attach using two #8-32x3/8” screws and 4mm lock washers. Press sideburner control knob onto valve stem. Note: Use left and right Note: Use upper and lower holes on fascia to holes on fascia to Control knob Control knob bezel Install bezel with “OFF” at top. Sideburner valve bracket Screws and Washers removed from valve bracket Valve stem #8-32x3/8” screw 4mm lock washer Sideburner fascia attach valve bracket attach bezel 9 Insert sideburner burner into left shelf.The stud on bottom of burner fits into rear small hole in sideburner drip pan onshelf, shown A.Secure burner to sideburner drip pan with one Wing nut, shown B. Make sure burner tube engages sideburner valve, shown C. BSideburner drip pan Wing nut Burner tube Valve C ASideburner burner Sideburner drip pan 10 1010 Under sideburner shelf, attach sideburner ignitor wire to electrode, shown A. Place sideburner grate onto sideburner shelf, aligning grate legs with holes in shelf, shown B. ASideburner Ignitor Wire Electrode Sideburner grate B 11 11 Insert front brace under control panel and between cart side panels. Make sure door hinge pins are on the top side and facing the front. Secure using two 1/4-20x1.” screws, 7mm lock washers, and 7mm flat washers on each side. NOTE: MAKE SURE THAT THE FRONT BRACE IS MOUNTED IN THE MOST DOWNWARD POSITION WHEN ASSEMBLED TO CART. Front brace 1/4-20x1.” screw 7mm lock washer 7mm flat washer Door Hinge Pin for clarity of illustrationNote: some parts omitted 12 1212 Inside of cart, insert rear shield tab into left slot on upper of lower back panel. Insert left and right grease tray rails into slotsbeneath grease tray opening in upper back panel, shown A. Attach front shield tabs under front brace and attach right and left rails under front brace with three #8x3/8” self-tapping screws, shown B. Tank heat shield Cart lower back panel Right rail Left rail A Rear FrontTank heat shield Front Brace Right railLeft rail #8x3/8” self-tapping screw Grease tray opening for clarity of illustrationNote: some parts omitted B*This side UP Tank heat shield 13 13 Insert hinge pin on bottom of doors into hole in bottom shelf. Press upper hinge pin in front brace, align hinge hole on top ofdoor, and release hinge pin into door. Left door Hinge pinon bottom of door Top ofdoor PRESS Right door 1414 Release the cap and nut from electronic ignition module. Attach electronic ignition module and heat shield to the cart right side panel with the nut and cap, shown A. Connect each of the wires from the main burner electrodes, and sideburner electrode into the back of the Electronic Ignition Module.Total (5) connections. Connect the two wires(A and B) from the switch wiring harness into the back of the Electronic Ignition Module. Total (2) connections. NOTE: Switch terminals are larger than electrode terminals and should only be installed in location shown as A,B. Wire 1 2 3 4 5 A B ignition module Electronic Heat shield Right side panel ANut Cap 15 Install flame tamers by sliding one end of each flame tamer into slots at front of firebox and resting opposite end on pins in back of firebox. Back of firebox Front of firebox Flame tamer Note: Some parts omitted forclarity of illustration Flame tamers Place cooking grates onto the firebox as shown. Insert the two wire ends at rear of warming rack into holes in back of16 firebox. Front wires of warming rack rest on sides of firebox. Note: Some parts omitted for clarity of illustration Assembled warming rack Warming rack Cooking grate 17 . LP CYLINDER IS SOLD SEPARATELY. Fill and leak check the cylinder before attaching to grill and regulator (see Use & Care sec...