valutazioni - 3, GPA: 4 ( )

Produttore : Allstar Products Group File Size : 1.33 mb File Nome : Lingua di insegnamento:

Close the door. If the down force adjustments are correct, the door will reverse within two seconds of contacting the object and travel to the Full Open position. If this does not occur, recheck the Limit Adjustments (Page 17) and Sensitivity Adjustments (Step 2 & 3, Above). NOTE: Any time adjustments are made to Limits or Sensitivity, YOU MUST RETEST THE OPENER FOR THE REVERSING FEATURE AT FLOOR LEVEL AS OUTLINED ABOVE. OPEN FORCE ADJUSTMENT CLOSE FORCE 104391 ADJUSTMENT 1 1/2” BLOCK OF WOOD LAID FLAT (2”X4”) 104392 F: OPERATION AND ADJUSTMENT INSTRUCTIONS F: OPERATION AND ADJUSTMENT INSTRUCTIONS A DAMAGED OR MALFUNCTIONING PHOTOELECTRIC ACCESSORY SYSTEM COULD ENABLE A GARAGE DOOR TO CLOSE ON PEOPLE OR PROPERTY, CAUSING SERIOUS INJURY OR DEATH. PERFORM THIS TEST MONTHLY TO ENSURE YOUR ALL-CLEAR IS WORKING PROPERLY. STEP 5: Testing the All-Clear™ Photosystem — Start the door in the close travel direction and then place an obstacle approximately 8" high by 12" wide in the path of the beam. The Red Pilot Light on the Allstar Access All-Clear™ Photosystem should go out. The door should stop and reverse to the full open position. With the door fully open and at rest, place the obstacle in the path of the beam once again. Activate the Standard Wall Push Button. The opener should revert to and remain in the PUSH AND HOLD mode of operation for close travel. IF THE GARAGE DOOR TRAVELS MORE THAN ONE INCH IN A DOWNWARD PATH AFTER RELEASING THE BUTTON, THE ALL-CLEAR™ IS MALFUNCTIONING. CHECK THE ELECTRICAL CONNECTIONS AND ALIGNMENT OF THE ALL-CLEAR™. STEP 6: Operating the Deluxe Wall Station Controls — The Deluxe Wall Station replaces standard doorbell-type pushbuttons toallow you to integrate fully with all the convenience and security features built into your Allstar 3000 Series garage door operator. 1. Operator Pushbutton — Red-backlighting. Used to start or stop the operator. The function of this pushbutton is automatically disabled when the Security slide switch is set to the “ON” position and the door is fully closed. 2. Operator Light Pushbutton —Yellow-backlighting. Turns the operator light on and off, but does not activate the door operator. The operator light will stay on until turned off using this pushbutton, or until door operation is initiated, which overrides the function of this pushbutton and automatically turns the light off after 4-1/2 minutes. 3. Security Switch — Prevents unwanted door operation from pushbutton, key switches, keyless entry systems, radio controls, etc. When the Security Switch is moved to the “ON” position, with the garage door fully closed, signals from all of these devices are locked out by the operator. Such devices will continue to work until the door is fully closed, allowing you to set the switch (when leaving on vacation, for example), leave the garage and close the door remotely. (NOTE: YOU WILL NOT BE ABLE TO OPEN YOUR GARAGE DOOR USING RADIO CONTROLS OR EXTERIOR ACCESS CONTROLS UNTIL THE SECURITY SWITCH IS RETURNED TO THE “OFF” POSITION. THIS MUST BE DONE FROM INSIDE THE GARAGE.) When the Security Switch is engaged, the red light behind the Operator Pushbutton is extinguished as an indication. The Operator Light Pushbutton will continue to function normally. 104394 Operator Pushbutton Operator Light Push button Security Switch 19 20 For Opener Models: 3000, 3500, 3500-P and J3500 104339 OPERATOR WIRING DIAGRAM 21 Your Allstar Residential Garage Door Opener is furnished with an enhanced All-Clear™ Photosystem. New features include: Time-Saving Electrical Connections. No screw terminals! Just strip the ends of the wires back 5/16 inch and plug them into the self-locking connector. This is the same feature as found on millions of duplex electrical outlets. Wires may be released using a small screwdriver. (To avoid damage to unit, the widest possible screwdriver head which will fit into slot should be used. Use a screwdriver head no narrower than 1/8 inch.) Universal Wiring Capabilities. The All-Clear™ Photosystem can be wired in series or parallel combinations. Virtually any existing wiring can be used. See the figures above. Improved Sunlight Immunity. Under certain conditions, direct sunlight can overpower photobeam systems. We have provided an extra internal shield to reduce sunlight problems. When required, the position of the transmitter and receiver may be interchanged with out rewiring. 102121 SERIES CONNECTION (RECEIVER FIRST) WIRING AUXILIARY EQUIPMENT INSTALLATION CHECKLIST BEFORE PLACING DOOR OPERATOR IN REGULAR SERVICE, MAKE SURE THAT: 1. THE FRONT AND REAR MOUNTS FOR THE OPENER ARE SOUND AND SECURE AND THE RAIL IS POSITIONED CORRECTLY ABOVE THE HIGH ARC OF THE DOOR, AND THAT THE OPENER IS POSITIONED OVER THE DOOR ACTION CENTERLINE. 2. FOR SECTIONAL DOORS AND ONE-PIECE DOORS WITH TRACKS, THE POSITION OF THE DOOR ARM, WITH THE DOOR CLOSED, IS SUCH THAT ITS CONNECTING POINT ON THE TROLLEY IS 5" TO 8" BEHIND ITS CONNECTING POINT ON THE DOOR BRACKET. THE DOOR ARM SH...

Scarica la tua

Per scaricare, digitare 2 cifre :