NEVER INSTALL THE MONITOR IN A PLACE WITHIN THE DRIVER'S VIEW. THIS IS NOT ONLY DANGEROUS, BUT IT IS ALSO ILLEGAL. 4) Once the mounting location of the monitor has been determined, there may be additional preparation work necessary, depending on the vehicle structure and installation method. Some of the steps that may be required are: A) Removal of the vehicle's dome light. B) The headliner may need to be trimmed. 8 MOUNTING THE VOD80 Figure 2 NOTE: Two of the mounting holes are located under th

• Repeat All- repeats the disc that is playing. • Off As you toggle through the options, the repeat option changes. The selected repeat option loops repeatedly until it is turned off. K. PLAYING MP3 DISCS MP3 is a digital audio format. An audio CD-quality song is compressed into the MP3 format with no significant loss of audio quality. CD-R / RW discs that have been encoded in MP3 format are compatible with this device. Insert a MP3 Disc, the DVD player will initialize the disc and the directory

Note: Audio recorded for the center speaker and subwoofer will be assigned to the front and 3-D rear speakers to obtain the optimum 3-D surround sound effect. 1 2 3 4 5 6 7 1.TV set or screen 2. Front or main left speaker 3.Subwoofer 4.Center speaker 5.Front or main right speaker 10 The ideal surround sound speaker configuration may vary according to room size and wall material. The figure below illustrates a typical arrangement. Hints: Front or main speakers and central speaker should be placed

The unit applies the latest state of the art electronics and is designed for use in hotels, offices, vehicles or your home. The DVD Player is constructed to provide years of reliable, trouble-free service, and is compact so that you can take it with you anywhere and is designed for quick and easy setup. Please read all documentation prior to using this product. The documentation will assist you in obtaining the best equipment performance. Save this manual for later use. Important Notice It is un

Before beginning this installation, carefully read through the following instructions. Use extreme care when cutting headliner material. Check for wiring or other componentry above headliner material. Cut only where indicated. Materials/ Tools required for this installation: 1. #2 Phillips screwdriver 2. Powered screwdriver or drill with adapter 3. T-45 TORX bit driver 4. Razor knife or similar 5. Awl or similar tool 6. 1/4” hex socket bit 7. 7/64" drill bit 8. Small chisel 9. Audiovox Series 64

dome light area. Align the front mounting tabs with the openings in the metal inner roof openings previously used to support the rear pod retainers. Slide bracket to rear of vehicle until flange contacts rear edge of recessed area. See Figure 7. FIGURE 7 7. Secure bracket to sheetmetal frame using four (4) # 8 x 3/4" HWH TEKS screws ( item 1 pg 2 ). Secure O.E.M. ground wire (if applicable) using one of the screws. See Figure 8. FIGURE 8 6 8. If vehicle is equipped with an electronic compass, un

Failure to do so may cause damage to console or installed components. Figure 16 2. Raise overhead console into approximate position and connect wiring to O.E. components. 3. Loosely fit console against headliner. Check that console is centered in vehicle and matches all contours of headliner. While supporting console in mounting position, loosely install using two (2) 6-32 X 3/4" screws (item 10 pg 2) through the smaller holes in bracket on console into threaded clips on mounting bracket. See Fi

7 Connection ....................................................................................... 8 Operation Front Control Panel ........................................................................... 11 Remote Control …………………………………………………..….12 Power Management System ……………………………………...14 Technical Information Specifications ……………………………………………………….15 Troubleshooting ……………………………………………………..16 2 General Information General Information Thank you for purchasing this 12.1" flat-screen TFT LCD mo

If the LCD panel or video monitor is used for television reception, video or DVD play, the LCD panel or video monitor must be installed so that these features will only function when the vehicle is in “park” orwhen the vehicle’s parking brake is applied. An LCD panel or video monitor used for television reception, video or DVD play that operates when the vehicle is in gear or when the parking is not applied must be installed to the rear of the driver’s seat where it will not be visible, directl

See Figure 1. 2. Lower console and disconnect wiring at (2) two locations. Lay console on workbench for modification later. See Figure 2. 3. Using rear edge of opening in headliner, carefully trim headliner as shown and install mounting bracket (item 5 pg 2). Make sure the 8” cut is centered in vehicle. Caution: Before cutting headliner material, check for wiring or other componentry above headliner. Cut only where indicated. Secure front of bracket to roof brace using (2) two O.E.M. screws, pre