Turn on your Vehicle Entertainment System (VES) and select the source input to which the FLO TVservice is connected. (Note: Watching the FLO TVservice for an extended period of time with the engine OFF will run down the vehicle's battery.) 2. The VES screen will show the FLO TV splash screen and then the FLO TV preview channel. 3. If you are not subscribed, subscribe to the FLO TVservice by calling 888-99-FLOTV or by going online to The Device ID and Authorization Code of the FLO TV module ar

You, as the driver, are solely responsible for the safe operation of your vehicle and the safety of your passengers according to your local traffic regulations. Do not use any features of this system to the extent it distracts you from safe driving. Your first priority while driving should always be the safe operation of your vehicle. Audiovox Electronics Corporation cannot accept any responsibility whatsoever for accidents resulting from failure to observe these precautions or safety instructio

See the drawing on page 5. 2) It is best to mount the video monitor to the roof structure without the mini-console first. There should be a gap between the headliner and the outer flange of the video monitor. The mini-console should be cut to full this gap. Apply masking tape to the outer surface of the mini-console in the areas where the cut will be made. 3) Mark the cut to follow the necessary contour of the roof. The suggested method of marking is as follows: A) First mark the narrowest point

Important Notice An LCD panel and/or video monitor may be installed in a motor vehicleand visible to the driver if the LCD panel or video monitor is used forvehicle information, system control, rear or side observation ornavigation. If the LCD panel or video monitor is used for televisionreception, video or DVD play, the LCD panel or video monitor must beinstalled so that these features will only function when the vehicle is in“park” or when the vehicle’s parking brake is applied. An LCD panel o

Remove Adhesive Backing and Apply IR LED to IR Yellow RCA (Video) White RCA (Audio Left) "Y" Adapter for use with Non-Stereo Installations Item# 5 Power Connector 4 Pin Accessory Harness - Optional Dome Light (P/N:8010730) Power Source CHOKE Auxillary video display 12 VDC Power and Ground INPUT VIDEO (Yellow) Line Out-R (Red) LINE OUT Patch Cord VIDEO RCA-Female RCA Male to Male Line Out-L (White) Line Out-V (Yellow) To Secondary AV Monitor Power Harness Item #3 Power Harness Item #3 OPTIONAL PO

SETTING THE PRESETS (FOR AM AND FM OR TV MODES) 1) Turn to the desired channel/broadcast frequency. 2) Press the SET button ; the display flashes. 3) Select desired Preset (1~6 button). SETTING THE SPEAKER MODE 1) With power off, Press the SET button five times to enter the speaker configuration mode. “I SP(or E SP)” appears on the VFD. 2) Press the 1 preset button to toggle between the “I SP” and “E SP” 3) When the desired mode is reached, press the ON/OFF button. - 17 Using the Remote Control

Before operating the unit, please read this manual thoroughly and retain it for future reference. IMPORTANT NOTES To prevent an electrical system short which could cause serious damage to the unit, the vehicle, or cause personal injury, please follow the safety recommendations below: • Should there be requirement to replace a blown fuse, remember to first disconnect all power and switch off the unit before fuse replacement. Use a fuse with the correct rating to avoid damaging the unit. • During

PREPARATION OF VEHICLE INTERIOR FIGURE 1 3. Install console mounting bracket (item 2 pg 2) over O.E. bracket on roof brace. Secure rear of bracket using (2) two O.E. screws. Secure front of bracket using (2) two #8 x 3/4" screws (item 1 pg 2) See Figure 2. INSTALLATION INSTRUCTION # 44-0026B 3 1. Carefully trim headliner as shown. Caution: Before cutting headliner material, check for wiring or other componentry above headliner. Cut only where indicated. Make sure that the 8 1/2" cut is centered

Rearward to the C- pillar. Down the C-pillar to the floor. Route the power lead to an accessory controlled source. Connect the ground lead to the vehicle chassis. Route the remaining wiring (RCA plugs, Remote Sensor extension, etc.) to the VCP location. See Figure 4. Connect per instructions included with the video system. If video system if to be used as a television, install an appropriate antenna per instructions included with the antenna. 6. Construct a jumper harness that will connect the v