valutazioni - 4, GPA: 3.8
(
)
)
|
Facilità d'uso
• Clean the unit carefully and store it in a dry place. • Make sure engine switch is off when transporting or storing. • When transporting in a vehicle, cover chain with chain cover. If situations occur which are not covered in this manual, take care and use good judgement. Contact your dealer if you need assistance. Pay special attention to statements preceded by the following words: WARNING! Indicates a strong possibility of severe personal injury or loss of life, if instructions are not followed. CAUTION! Indicates a possibility of personal injury or equipment damage, if instructions are not followed. NOTE! Helpful information for correct function and use. 3 custsvc@tanaka-ism.com 3. Assembly procedures Owner.s ManualTCS-3401 WARNING! Never try to start engine without side case securely fastened. 1. Remove chain bar clamp nuts. 2. Remove the side case (1) while pinching the rear part of the side case (1) .(Fig.1 -1) Install the spiked bumper (1) (if so equipped) to the unit with the two screws. (Fig. 1 -1 B) 3. Install, the chain bar (1) onto the bolts (2), then push it toward the sprocket (3) as far as it will go. Make sure that the boss of chain tension adjust bolt (4) fits into the hole of the bar (5). (Fig. 1-2) NOTE! Slightly move the bar back and forth and make sure the chain tension boss (4) fits into the hole (5) in the bar properly. 4. Confirm the direction of saw chain (1) is correct as in the figure, and align the chain on the sprocket. (Fig. 1-3) 5. Guide the chain drive links into the bar groove all around the bar. 6. Install the side case (1) onto the guide bar clamp bolts after inserting it on the alignment/locking tab on the engine case (2). (Fig. 1 - 1 ) Then fix the clamp nuts temporarily. 7. Raise the bar end, and tighten the chain (1) by turning the tension adjustment bolt (2) clockwise. To check proper tension, lightly lift up the center of chain and there should be about 0.51.0 mm clearance between bar and edge of drive link (3). (Fig.1 -4, 5) CAUTION! • PROPER TENSION IS EXTREMELY IMPORTANT! 8.Raise the bar end and securely tighten the chain bar clamp nuts with the box wrench. (Fig. 1 -4) 9.A new chain will stretch so adjust the chain after a few cuts and watch chain tension carefully for the first half hour of cutting. NOTE! Check the chain tension frequently for optimum performance and durability. CAUTION! • When the chain is excessively tightened, the bar and chain will be damaged rapidly. Conversely, when the chain is excessively loosened, it may get out of the groove in the bar. • Always wear gloves when touching the chain. WARNING! During operation, hold chain saw firmly with both hands. A single hand operation may cause serious injury. 4 custsvc@tanaka-ism.com Owner.s ManualTCS-3401 TCS-3401 4. Operating procedures Fuel (Fig. 2-1) WARNING! The chainsaw is equipped with a two-stroke engine. Always run the engine on fuel, which is mixed with oil. Provide good ventilation, when fueling or handling fuel. Fuel • Always use branded 89 octane unleaded gasoline. • Use Tanaka two-cycle oil or a quality two-cycle oil at mixing ratio of 25-50:1 (Gasoline (A) : Oil (B)), only for the state of California at 50:1. • Never use multi-grade oil (10 W/30) or waste oil. • Always mix fuel and oil in a separate clean container. • Always start by filling half the amount of fuel, which is to be used. Then add the whole amount of oil. Mix (shake) the fuel mixture. • Add the remaining amount of fuel. • Mix (shake) the fuel-mix thoroughly before filling the fuel tank. Fueling WARNING! • Always shut off the engine before refueling. • Slowly open the fuel tank, when filling up with fuel, so that possible over-pressure disappears. • Tighten the fuel cap carefully, after fueling. • Always move the unit at least 3 m (10 ft.) from the fueling area before starting. Before fueling, clean the tank cap area carefully, to ensure that no dirt falls into the tank. Make sure that the fuel is well mixed by shaking the container, before fueling. 5 custsvc@tanaka-ism.com Owner.s ManualTCS-3401 TCS-3401 CHAIN OIL (Fig. 2-1 B) Fill chain oil reservoir (2). Always use good quality chain oil. When the engine is running, the chain oil is automatically discharged. NOTE! When pouring fuel (1) or chain oil (2) into the tank, place the unit with cap side up. (2) ADJUSTMENT OF CHAIN OIL SUPPLY The chain oil quantity discharged through the lubrication system is factory-adjusted to the maximum. Adjust the quantity in accordance with the operating condition. Turn the adjusting screw (1) counterclockwise to decrease the quantity and turn it clockwise to increase the quantity. (Fig. 2-1 C) Do not try to turn the screw beyond level marks. Starting (Fig. 2-2, 3) WARNING! When the engine starts with the throttle lock engaged, the engine speed is high enough to make the chain rotate. CAUTION! Before starting, make sure chain brake is disengaged (if s...
Questo manuale è adatto anche per i modelli :Benzo e seghe - TCS-3401 (644.6 kb)
Benzo e seghe - TCS-3401 (644.6 kb)