WARNING: Cutting edges on chain are sharp. Use protective gloves when handling chain. IMPORTANT: Do not clamp chain saw in vise during assembly. Continued CHAIN SAW NAMES AND TERMS Continued 5. Rotate guide bar retainer 90 degrees as shown in Figure 5. 6. Place chain around drive sprocket, along top groove of guide bar, and around guide bar nose. Note: Make sure cutting edges of chain are facing in right direction. Position chain so cutting edges on top of guide bar face guide bar nose (see Figu

Step 2a Step 3 Step 2b ® ELECTRIC CHAIN SAW OWNER’S MANUAL IMPORTANT! Failure to follow these instructions when tensioning saw chain will damage saw and void the warranty. For additional information see owner’s manual or call 1-800-858-8501. Make sure chain moves freely around guide bar then tighten nut. LOOSEN Loosen nut... If chain becomes loose around guide bar, allow chain to cool then... TIGHTEN Turn chain tensioning screw clockwise to tension saw chain... TIGHTEN WARNING: Unplug saw and al

Watch your footing while exiting area. 108539 18 OPERATING CHAIN SAW Continued LIMBING A TREE WARNING: When cutting limb that is under tension, use extreme caution. Be alert for wood springing back. When wood tension is released, limb could spring back and strike operator causing severe injury or death. WARNING: Avoid kickback. Kick- back can result in severe injury or death. See Kickback, page 3, to avoid risk of kickback. Limbing is removing branches from a fallen tree. Make sure your footing

Improper use of saw can cause severe injury. Keep this manual for future reference. CSA Classification for this saw is 2C; The consumer chain saw intended for general use by home owners, cottagers, etc., and for such general applications as clearing, pruning, cutting firewood, etc. ® ® ELECTRIC CHAIN SAW INFORMATION SYMBOLS Read Instruction Manual Do Not Expose to Rain or Use in Wet Conditions Remove Plug Immediately if Cable is Damaged or Cut Hold Chain Saw with Both Hands Beware of Kickback He

Broad Street Angier, NC 27501 8611 Rt. US 60 8614 Church Lane Corinth, MS 38834 Richard’s Sharpening Service 919-331-0463 Ashland, KY 41102 606-928-4932 Randalstown, MD 21133 410-655-0801 662-287-2460 824 Mill Road Northfield, NJ 08225 609-641-9481 Leonard Electric Motor Repair, Inc. 531 N. Fayetteville St. Asheboro, NC 27203 336-625-2375 107990 21 For more information, visit ® ® ELECTRIC CHAIN SAW Martin Equipment Company United Rentals of North America Raymond, M. Nolt Corpus Christi Power Too

WARNING: Do not cut limbs higher than your shoulders. Continued 9 For more information, visit ® ® ELECTRIC CHAIN SAW OPERATING CHAIN SAW Continued FELLING A TREE (Cutting Down a Tree) WARNING: • Avoid kickback. Kickback can result in severe injury or death. See Kickback,page 3, to avoid risk of kickback. • Do not fell a tree without ample skill or expert help. • Keep children, animals, and bystanders away from area when felling a tree. • If two or more persons perform bucking and felling operati

Flat File Cleaning Groove Burr With Putty Knife Oil Slot Guide Bar Figure 18 - Guide Bar Maintenance SHARPENING YOUR SAW CHAIN WARNING: Unplug chain saw from power source before servicing. Severe injury or death could occur from electrical shock or body contact with moving chain. WARNING: Cutting edges on chain are sharp. Use protective gloves when handling chain. Keep chain sharp. Your saw will cut faster and more safely. A dull chain will cause undue sprocket, guide bar, chain, and motor wear.

Trigger Device that turns saw on and off. Squeezing trigger turns saw on. Releasing trigger turns saw off. Trimming (Pruning) Process of cutting limb(s) from a living tree. Undercut An upward cut from underside of log or limb. This is done while in normal cutting position and cutting with top of guide bar. ments when used with other saws. Keep this manual for reference. It is your guide to safe and proper operation of this chain saw. 100583 5 ® ® ELECTRIC CHAIN SAW PRODUCT IDENTIFICATION Power C

•Reduce the risk of the saw chain breaking or jumping off the bar. •Obtain optimal cutting performance. •Extend the life of cutting equipment. •Avoid increasing vibration levels. General rules •Only use cutting equipment recommended by us! See instructions under the heading Technical data. •Keep the chain’s cutting teeth properly sharpened! Follow our instructions and use the recommended file gauge. A damaged or badly sharpened chain increases the risk of accidents. •Maintain the correct depth g

Either of these reactions may cause you to Iose control of the saw, which could result in serious personal injury. • Do not rely exclusively on the safety devices built 5. For safe operation English Fraanccaaiis EEssppaannooll 5. Consignes de securite 5. Instrucciones de seguridad 16. Toujours arreter le moteur avant de poser la tronconneuse. 17. Observer la plus grande prudence en coupant les broussailles. Une liane ou un arbrisseau se prenant dans la chaine risquent de faire perdre l’equilibre