valutazioni - , GPA: ( )

Istruzioni per l'uso Burley, Modello PRE-2005

Produttore : Burley
File Size : 502.42 kb
File Nome :

Lingua di insegnamento:

Il documento viene caricato, si prega di attendere

Scarica la tua primo

Il documento viene caricato, si prega di attendere

Scarica la tua primo

• Save the hitch and the d-ring (#3) for reinstallation. The locking nut (#5) and the bolt (#1) can be discarded. A longer bolt is provided for the next step. Always check the handle attachment before using. Be sure that handle is properly installed with buttons protruding in the locked position. Failure to do this could lead to loosening of handle, loss of control, and serious injury. 3 1 2 5 4 8 Burley Walk ‘n Roller Manual; models 2003 and earlier Re-Assembly with the Pivot Wheel • Slide the wheel pivot assembly over the end of the tongue so that the hole in the tongue lines up with the hole in the top as shown below. • Line the hitch connector hole #4 with those same two holes. • Run the 2-inch bolt provided through the d-ring, and then through the Wheel pivot assembly, tongue hitch connector. • Push the bolt through the hole at the bottom, visible in the cavity underneath, and then secure with the new locking nut provided (tighten to 6 ft-lbs). The end of the bolt should be fl ush or completely pass through the end of the nut. • Place the 1-inch bolt (#2) using 2 washers as shown and a locking nut. • Then place the other 1-inch bolt (#3) through one washer and the remaining hole. • On the underside of #3 place the safety strap and a locking nut. • Tighten to 6 ft-lbs using the torque wrench. The end of the bolt must be fl ush with or completely pass through the nut. When installed the hitch is re-attached by the bolt that goes through the tongue (and hitch’s fl exible coupling); the safety strap is anchored, and the d-ring is on top. Note: If using the Burley Alternative Hitch, the fl exible coupling is attached in the same manner, using the bolt through the tongue. The safety strap is anchored in the same way, to the wheel assembly clamp bolt. 2 3 5 4 1 Bolt must go through hole in flexible coupling. Otherwise, hitch could come loose causing an accident resulting in injury or death. Bolt must go through hole in flexible coupling. Otherwise, hitch could come loose causing an accident resulting in injury or death. VI. Using the Walk n’ Roller Wheel The wheel has two positions. One is for use as a trailer,“bike” position.The other is for use as a stroller,“stroll” position. Before changing engage the parking brake. To rotate the wheel, loosen the knob, #1. This will loosen the triangular pivot clamp, #2, enough to rotate.Then rotate to either the “bike” or “stroll” position as needed. Then tighten the knob. Do not attempt to hitch the trailer to the bike with the wheel in “stroll” position. 12 VII. Installing the Brake Note: If you have a 2004 Encore, this step is unnecessary. Parts Needed for Brake Installation: (1) brake assembly (1) .” x 1.5” hex head bolt (1) .” nut Locate the gap in the trailer fabric that is behind the right wheel.The gap exposes a 1 inch diameter, aluminum main frame tube that runs along the inside of the wheel. Undo the clamp in the brake assembly by removing the 1.5 inch long hex head bolt. Burley Walk ‘n Roller Manual; models 2003 and earlier Clamp the brake assembly onto the frame tube as shown.The clamp should be oriented so that the bolt runs underneath the main frame tubing. Fasten with the bolt and nut through the clamp, but do not tighten. Adjust the brake by sliding backward or forward as needed before tightening. You will need to pull the brake handle backward to move the brake to engaged position (see next image). tighten the bolt. Burley Walk ‘n Roller Manual; models 2003 and earlier With the brake in engaged position, handle back, slide the brake forward until the post is just touching the tire. Mark this position on the frame.Then rotate the handle forward to disengage the brake, and slide the brake forward about . from the mark. Now Once tightened, engage the brake to verify its function.The brake post should push into the tire about . inch, or half the diameter of the post. Check brake before strolling, jogging, or bicycling; or after changing a tire, or any wheel removal. Failure to do so could result in serious injury. Check brake before strolling, jogging, or bicycling; or after changing a tire, or any wheel removal. Failure to do so could result in serious injury. VIII. Safety Guidelines Using your Walk n’ Roller, bicycling with a trailer, and bicycling in general can be hazardous. Failure to obey the following Safety Guidelines could result in serious injury or death. • Walk n’ Roller must be operated by a responsible adult. • Wear street shoes. Do not wear roller or in-line skates, as you may lose balance or be unable to emergency stop. • Check handle is secure, button protruding through handle receivers. • Always wear wrist tether and hold securely onto handle when jogging or strolling. • Set parking brake before release of handle to prevent loss of contol. • Do not stroll with or jog with headphones, radios, cell phones, or other distractions as you will be unable to hear oncoming vehicles or other hazards. • Do not use Walk n’ Roller on stairs of escalato...