valutazioni - 6, GPA: 3.3
(
)
)
|
da questo dispositivo ha anche altre istruzioni :
Facilità d'uso
1 Select the folder. See “Selecting the Folder”. 2 Select the message number. * The display selected with the MENU/DISPLAY button appears (see the reverse side). 3 Start playback. After playing back one message, the unit stops at the beginning of the next message. When the continuous play function is set to “ON” (see the reverse side), the unit stops after playing all messages in a folder. When the last message on a folder has been played back, the unit stops at the beginning of the last message. For private listening Connect an ear receiver or headphones (not supplied) to the i (earphone) jack. The built-in speaker will be automatically disconnected. If noise is heard, wipe the headphones plug. Other operations To Do this stop at the current position Press NxPLAY/STOP or xSTOP. To resume playback from that point, press NxPLAY/STOP again. go back to the beginning Press – . once. of the current message skip to the next message Press >+ once. go back to previous Press – . or >+ repeatedly. messages/skip to succeeding (During stop mode, keep the button messages pressed to skip the messages continuously.) 1 Slide and lift the battery compartment lid. 2 Insert two LR03 (size AAA) alkaline batteries with correct polarity, and close the lid. Clock setting display appears when you insert batteries for the first time, or when you replace the batteries with new ones. Please refer to Steps 2 to 3 in “Step 2: Setting the Clock” to set the date and time. IC Recorder Operating Instructions .2005 Sony Corporation Printed in China ICD-B120 Owner’s Record The model number is located at the rear and the serial number is located inside the battery compartment. Record the serial number in the space provided below. Refer to these numbers whenever you call upon your Sony dealer regarding this product. Model No. ICD-B120 Serial No. _____________________________________ Step 1: Installing the Batteries Replacing the batteries The battery indicator in the display window shows the battery condition. When flashes, replace the batteries with new ones. When flashes, the batteries are exhausted and the unit will stop operation. Battery life* With continuous use, approx. 11 hours recording/7.5 hours playback in the HQ mode, and approx. 22 hours recording/11 hours playback in the SP and LP modes is possible. * Using Sony alkaline batteries LR03 (size AAA) * When playing back through the internal speaker with the medium volume level The battery life may shorten depending on the operation of the unit. Notes • Do not use manganese batteries for this unit. • When you replace the batteries with new ones, the clock setting display appears. In this case, set the date and time again. The recorded messages and alarm setting, however, will remain. • When replacing the batteries, be sure to replace both batteries with new ones. • Do not charge dry batteries. • When you are not going to use the unit for a long time, remove the batteries to prevent damage from battery leakage and corrosion. • The unit is accessing data while “ACCESS“ appears in the display window. While accessing, do not remove the batteries. Doing so may damage the data. Clock setting display appears when you insert batteries for the first time, or when you replace the batteries with new ones. In this case, proceed from step 2. 1 Display the clock setting display. 2 Set the date. 3 Set the time. Tip This unit does not have a power on/off switch. The display is shown at all times. 2 Press NxPLAY/STOP. The month digits will flash. 3 Set the month and day in sequence, then press NxPLAY/STOP. The hour digits will flash. 2 Press – . or >+ to display “SET DATE”. 3 Press NxPLAY/STOP. The year digits will flash. Tip To set the date to Year 2005, display “05Y”. Step 2: Setting the Clock Recording Messages You can record up to 99 messages in each of the four folders (A, B, C, and D). Since a newly recorded message is automatically added behind the last recorded message, you can start recording quickly without searching for the end of the last recording. e.g. Message 1 Message 2 Newly recorded message Blank space Note Before making a long recording, be sure to insert new batteries and check the battery indicator. 1 Select the recording mode. See “Changing the Recording Mode” on the reverse side. 2 Select the folder. See “Selecting the Folder”. 3 Start recording. You do not need to keep pressing zXREC/PAUSE while recording. 4 Stop recording. If you do not change the folder after you stop recording, the next time you record you will record in the same folder. To Do this pause recording* Press zXREC/PAUSE. During recording pause, the OPR indicator flashes in red and “PAUSE” flashes in the display window. release pause and Press zXREC/PAUSE. resume recording Recording resumes from that point. (To stop recording after pausing recording, press xSTOP.) listen to the current Press xSTOP to stop recording, then press recording NxPLAY/STOP. review the current Press NxPLAY/STOP during recording. recording...