valutazioni - 4, GPA: 5
(
)
)
|
Facilità d'uso
A good earth ground is a metal stake driven into moist earth. DEO ANTENNA R SURRO AUDIO OUTP DVR CD S N OUT CD-R (REC)(PLAY) DVR AM GND FM UNBAL. 75 N OUT MONITOR OUT MD/ OUTIN extended outdoors from a window. Ground For maximum safety and minimum Connecting the wire of the AM loop antenna Connecting the power cable Once all connections are complete, plug the power cable into the AC wall outlet. L Power cable To the AC wall outlet Turning on and off the power Turning on this unit Press ASTANDBY/ON (or cPOWER) to turn on this unit. y • When you turn on this unit, there will be a 4 to 5-second delay before this unit can reproduce sound. Set this unit to the standby mode Press ASTANDBY/ON (or bSTANDBY) to turn off this unit. Note • In the standby mode, this unit consumes a small amount of power in order to receive infrared signals from the remote control. PREPARATION Open the lever Insert Close the lever Assembling the supplied AM loop antenna Note • The types of the supplied AM loop antenna is different depending on the models. 15 En English Optimizing the speaker setting for your listening room (YPAO) Optimizing the speaker setting for your listening room (YPAO) This unit has the Yamaha Parametric Acoustic Optimizer (YPAO). With the YPAO, this unit automatically adjusts output characteristics of your speakers based on speaker positions, speaker performances, and acoustic characteristics of the room. We recommend that you first adjust the output characteristics with the YPAO when you use this unit. Notes • Be advised that it is normal for loud test tones to be output during the “AUTO SETUP” procedure. Do not allow small children to enter the room during the procedure. • To achieve the best results, make sure that the room is as quiet as possible while the “AUTO SETUP” procedure is in progress. If there is too much ambient noise, the results may not be satisfactory. Using AUTO SETUP y • Initial settings are indicated by (*) in the following each parameter. 1 Make sure of the following check points. Before starting the automatic setup, check the following check points. • All speakers and subwoofer are connected appropriately. • Headphones are disconnected from this unit. • This unit is turned on. • The connected subwoofer is tuned on and the volume level is set to about half way (or slightly less). • FRONT A speakers are selected as the front speaker system (see page 19). • The room is sufficiently quiet. • The crossover frequency control of the connected subwoofer is set to the maximum. CROSSOVER HIGH CUT VOLUME MIN MAX MIN MAX Controls of a subwoofer (example) 2 Connect the supplied optimizer microphone to the OPTIMIZER MIC jack on the front panel. “SETUP•••••AUTO” appears on the front panel display. 3 Place the optimizer microphone at your normal listening position on a flat level surface with the omni-directional microphone heading upward. Optimizer microphone y • We recommend that you use a tripod (etc.) to affix the optimizer microphone at the same height as your ears would be when you are seated in your listening position. You can use the attached screw of a tripod (etc.) to fix the optimizer microphone to the tripod (etc.). 4 Press ol / h to select “AUTO.” Choice Function AUTO* Automatically runs the entire “AUTO SETUP” procedure. RELOAD Reloads the last “AUTO SETUP” settings and overrides the previous settings. UNDO Undoes the last “AUTO SETUP” settings and restores the previous settings. DEFAULT Resets the “AUTO SETUP” parameters to the initial factory settings. Note • “RELOAD” or “UNDO” is available only when you have previously run “AUTO SETUP” and confirmed the results. 5 Press oENTER to start the setup procedure. This unit starts the automatic setup procedure. Loud test tones are output from each speaker during the audio setup procedure. After all settings (“INITIALIZING,” “WIRING/LEVEL,” “DISTANCE,” “SIZE”) are sequentially completed, “FINISH” appears on the front panel display. y • To cancel the automatic setup, press ok. 16 En Optimizing the speaker setting for your listening room (YPAO) Notes • During the automatic setup procedure, do not perform any operation on this unit. • We recommend that you get out of the room while this unit is in the auto setup procedure. It takes approximately 3 minutes for this unit to complete the auto setup procedure. 6 When all measurements are completed successfully, “FINISH” appears on the front panel display. The result of the automatic setup for each speaker appears in order on the front panel display. The distance between the speaker and the listening position FL: 3.3m +2 Speaker FL/FR: Front left/right C: Center SL/SR: Surround left/right SW: Subwoofer The result of the adjustment of the volume level y • To display the result of the automatic setup again, press lk / n repeatedly. Notes • If you select “RELOAD” in step 4, no test tones are output. • If an error occurs during the “AUTO:CHECK” procedure, the setup procedure is canceled and an error screen appe...
Questo manuale è adatto anche per i modelli :Home theater - YHT-392 (2.53 mb)