Produttore : Bosch
File Size : 1.24 mb
File Nome :
|
Facilità d'uso
The tool speed can be controlled from the minimum to the maximum nameplate RPM by the pressure you apply to the trigger. Apply more pressure to increase the speed and release pressure to decrease speed. This accurate speed control enables you to drill without center punching. It also permits you to use as a power screwdriver. Bits are available for driving screws as well as running bolts and nuts. FORWARD/REVERSING LEVER & TRIGGER LOCK Your tool is equipped with a forward/ reversing lever and trigger lock located above the trigger (Fig. 1). This lever was designed for changing rotation of the chuck, and for locking the trigger in an “OFF” position to help prevent accidental starts and accidental battery discharge. For forward rotation, (with chuck pointed away from you) move the lever to the far left. For reverse rotation move the lever to the far right. To activate trigger lock move lever to the center off position. !CAUTION Do not change direction of rotation until the tool comes to a complete stop. Shifting during rotation of the chuck can cause damage to the tool. GEAR SHIFTING Your tool is equipped with two separate gear ranges, low gear and high gear. Low gear provides high-torque and slower drilling speeds for heavy duty work or for driving screws. High gear provides faster speeds for drilling lighter work. To change speeds slide switch, to the high or low position. ATTENTION: If your tool appears to be running, but the chuck will not turn, check to make sure the gear shifting switch is pushed fully into desired setting. ADJUSTABLE CLUTCH Your tool features 15 clutch settings. Output torque will increase as the clutch ring, is rotated from 1 to 15. The drill “ ” position will lock up the clutch to permit drilling and driving heavyduty work, and also enables bits to be changed quickly and easily in the keyless chuck. BRAKE When the trigger switch is released it activates the brake to stop the chuck quickly. This is especially useful in the repetitive driving and removal of screws. BIT STORAGE ADAPTER Your tool is equipped with a bit storage adapter that will allow you to store a longer bit if desired. To install bit adapter, remove bit from standard storage area, then snap adapter into it’s place. To use, hold bit adapter in place when removing bit (Fig. 1). INSERTING BITS REMOVING CHUCK Move reverse switch lever to the center “OFF” Rotate the clutch ring to the drill bit position. Remove battery pack and rotate the symbol “ ”. Open the chuck all the way, clutch ring to the drill bit symbol remove left-hand thread screw inside chuck “ ”. Rotate the chuck sleeve counter-by turning it clockwise (Fig. 2). clockwise viewing from chuck end, and open chuck to approximate drill bit diameter. Insert a clean bit up to the drill bit flutes for small FIG. 2 CHUCK bits, or as far as it will go for large bits. Close SLEEVE chuck by rotating the chuck sleeve clockwise and securely tighten by hand. !WARNING Do not use the power of the drill while grasping chuck to loosen or tighten bit. Friction burn or hand injury is possible if attempting to Insert the short arm of a 3/8" hex key wrench grasp the spinning chuck. and close jaws on flats of wrench (Fig. 3). -9 BM 2610925941 6-05 6/10/05 10:21 AM Page 10 Strike long arm of wrench sharply counterclockwise, remove wrench and unthread chuck from spindle (Fig. 3). INSTALLING CHUCK Always keep the spindle threads, the threads of the chuck and securing screw free of debris. To install a chuck, reverse “removing the chuck” procedure. FIG. 3 RELEASING AND INSERTING BATTERY PACK Release battery pack from tool by pressing pack. To insert battery, align battery and slide on both sides of the battery release tabs and battery pack into tool until it locks into pull downwards. Before inserting battery position. Do not force. pack, remove protective cap from battery IMPORTANT CHARGING NOTES 1. The battery pack accepts only about 80% of its maximum capacity with its first few charge cycles. However, after the first few charge cycles, the battery will charge to full capacity. 2. The charger was designed to fast charge the battery only when the battery temperature is between 40°F (4°C) and 105°F (41°C). 3. A substantial drop in operating time per charge may mean that the battery pack is nearing the end of its life and should be replaced. 4. If you anticipate long periods (i.e. a month or more) of non-use of your tool, it is best to run your tool down until it is fully discharged before storing your battery pack. After a long period of storage, the capacity at first recharge will be lower. Normal capacity will be restored in two or three charge/discharge cycles. Remember to unplug charger during storage period. 5. If battery does not charge properly: a. Check for voltage at outlet by plugging in some other electrical device. b. Check to see if outlet is connected to a light switch which turns power “off” when lights are turned off. c. Check battery pack terminals for dirt. Clean with c...
Questo manuale è adatto anche per i modelli :Trapani e shuropopverty - 32612 (1.24 mb)
Trapani e shuropopverty - 32614 (1.24 mb)
Trapani e shuropopverty - 32609 (1.24 mb)