This feature will lock the bit holder in one position when the trigger switch is released. This will allow you to tighten or loosen a nut or screw by rotating the tool by hand with the switch off. This is convenient when higher turning torque is needed. BUILT IN WORK LIGHT Your tool is also equipped with a light that turns on automatically when the switch is activated, for better visibility when drilling/driving (Fig. 1). INSERTING AND RELEASING BATTERY PACK Release battery pack from tool by

turn the unit off (Fig. 1). The target temperature can be increased in When heat gun is used in an enclosed steps of 10°F by pressing the “+” side of the container, such as a shrink tunnel or special temperature button or reduced by pressing the enclosure, ambient air must be allowed to “–” side of the button. Brief pressing of the pass into the heat gun and there must be an button increases or decreases the target outlet of equal size for the heated air to pass out of the enclosure also. Total

Sem. T-25 (2) 52 18-74-0120 220 V. Field (1) 53 23-16-1410 Motor Insulator (1) 54 22-20-0680 Brush Tube (2) 55 22-18-0706 Carbon Brush Assembly (2) 56 06-82-8835 8-32 x 5/16" Pan Hd. Sem.T-20 (2) 57 22-56-0470 Terminal Block (1) 58 22-38-0140 Wire Trap (1) 59 31-17-0200 Cord Clamp (1) 60 06-82-7326 8-16 x 1" Pan Hd. Plastite T-20 (2) 61 23-37-0150 Control Assy. (See Bull. 58-03-0020) (1) 62 06-72-1720 Service Rivet (2) 63 12-99-1875 Service Nameplate (1) 64 22-32-0350 Brush Cover (2) 65 06-82-53

Enduisez le pivot d’une mince couche de graisse MILWAUKEE de type «E». 3. Replacez le manchon sur le pivot. assurez-vous que le manchon du pivot tourne librement sur le pivot et ensuite, remettez l’anneau de retenue en place. page 26 Remplacement du joint d’etancheite des coussins a vide Pour les modeles 4115, 4125 et 4130 seulement. A l’usage normal, le joint d’etancheite en caoutchouc sous le coussin a vide vient a s’user et il faut le remplacer. Faites remplacer le joint d’etancheite du couss

б No. 23-37-0200 Meter Box - Complete FIG. PART NO. DESCRIPTION OF PART NO. REQ. 1 06-75-3200 Screw (1) 2 06-81-5660 Screw (2) 3 06-82-5270 Screw (2) 4 06-55-3870 Nut (2) 5 22-04-0030 Meter (1) 6 22-12-0185 Box Body (1) 7 22-64-0195 Power Cord (1) 8 22-68-0175 Box Cover (1) 9 23-66-3030 Switch (1) 10 23-36-3200 Plug (1) 11 31-01-2030 Meter Cover (1) 12 44-76-0185 Cord Strain Relief (1) 13 44-76-0385 Straight Thru Fitting (1) 14 22-33-0030 Suppressor (1) 15 10-98-3030 Ground Lab

A gap indicates a misplaced wire or component. • Tighten breaker boot (5) after installing cover (13). • Cord jackets (12 and 15) are to extend a minimum of .125" beyond cord clamps (10), 2 places. Cord set (12) is shown inside cord protector (11). • Ground label (18) is to be applied to the inside of the enclosue (8), under the terminal block (17). • Tuck the red leadwire assembly (3) down below pegs. ITEM PART NUMBER DESCRIPTION QTY. 1 22-68-0200 SWITCH BOOT (Not Shown) (1) 2 23-66-1430

LISBON RD., BROOKFIELD, WI 53005 Drwg. 3