valutazioni - 3, GPA: 2.7
(
)
)
|
Facilità d'uso
62. DVD/VCR VIDEO OUT Jack Connect the yellow video cable (supplied) here and to the TV’s Video In jack. 63. ANT-OUT (Antenna Out) Jack Use the supplied RF coaxial cable to connect this jack to the ANTENNA IN Jack on your TV. Caution: Do not touch the inner pins of the jacks on the rear panel. Electrostatic discharge may cause permanent damage to the player. DISPLAY DISPLAYS DURING OPERATION Stays on when the inserted disc is being played back. Lights up when a CD is inserted into the tray. Lights up when the inserted disc comes to a pause. Stays on when the A-B repeat function is on. Stays on when the repeat function is on. Stays on when repeat track function is on. Displays how long a current title or track has been played back. When a chapter or track has switched, the number of the a title, chapter or track is displayed. Stays on when repeat title function is on. Stays on when repeat chapter function is on. Stays on during playback when the repeat function is on. DVD Lights up when a DVD is inserted into the tray. VCR Lights up when the playback is in a still or in a slow mode. Works as a clock, or a tape counter. Stays on when the inserted Also displays a channel number, cassette is being played back. and remaining time for OTR No disc inserted or playing DVD menu Tray open Tray closed Loading the Disc LOADING THE BATTERIES 1. Open the battery compartment cover. 2. Insert two AA batteries, with each one oriented correctly. 3. Close the cover. Notes .Do not mix alkaline and manganese batteries. .Do not mix old and new batteries. –11– EN 1L25 VCR/DVD SWITCHING Because this product is a combination of a VCR and DVD player, you must first select which component you wish to operate with the OUTPUT BUTTON. VCR MODE DVD MODE Press VCR on the remote control. Press DVD on the remote control. (Verify that the VCR OUTPUT Light is lit.) (Verify that the DVD OUTPUT Light is lit.) Notes .Pressing only OUTPUT on the front panel does not switch the mode of the remote control. You always need to select the correct mode on the remote control too. POWER CHANNEL PLAY STOP/EJECT VIDEOVCR AUDIO REW OPEN/CLOSE F.FWD STOP PLAY RECVCRDVD TIMER REC OUTPUT DVD VCRDVD TIM OUTPUT DVD button DVD OUTPUT Light VCR button VCR OUTPUT Light OUTPUT button + 1 2 3 4 5 6 7 8 9 0 10 SPEED AUDIO POWER SKIP/CH. SLOW VCR/TV DISPLAY PAUSE PLAY STOP RECORD ENTER RETURNTITLE MENU SETUP CLEAR/ C.RESET ZOOMMODE A-BANGLE SEARCH MODE REPEAT SUBTITLE T-SET DVD VCR –12– EN 1L25 HOOKUPS CAUTION: .Be sure to turn off the DVD/VCR COMBINATION UNIT and equipment to be connected. .Read through the operation manual for the equipment to be connected. .Be sure that the colors of the jacks and plugs match up when using VIDEO/AUDIO cables. .Be sure to keep the DVD/VCR COMBINATION UNIT connection cables separate from the TV antenna cable when you install the DVD/VCR COMBINATION UNIT, because it may cause electrical interference when you are watching television programs. CONNECTING TO A TV WITHOUT A/V TERMINALS 1. Disconnect the AC power cord of the TV from the [VHF/UHF[Indoor antenna] [Back of the DVD/VCR] AC outlet. 2. Disconnect the antenna or cable from the TV. 3. Connect the antenna or cable to the ANT-IN jack of the DVD/VCR COMBINATION UNIT. 4. Connect the DVD/VCR COMBINATION UNIT to the TV using the RF cable. 5. Plug the AC power cords of the DVD/VCR COMBINATION UNIT and TV into the AC outlets. RF OUTPUT CHANNEL for DVD/VCR 1. Connect the DVD/VCR COMBINATION UNIT to a TV using RF cable (see above steps). 2. Select channel 3 on your TV. 3. Press PLAY. .If noise appears, change the RF output channel of the DVD/VCR COMBINATION UNIT to channel 4 by pressing PLAY on the VCR for 3 seconds during playback. .There is case that the RF output channel does not change by situation (For example, when you adjust tracking using CHANNEL ( ) ). In this case, stop the playback, and start the playback again. After that, press PLAY on the VCR for 3 seconds. .If there is a power failure or the DVD/VCR COMBINATION UNIT is unplugged for more than 30 seconds, the RF output channel setting will return to CH3. UHF/VHF combination antenna] IN OUT [Cable box or satellite box] OR [Back of the UHF/VHF combination TV] RF cable (supplied) From Cable or Satellite Company OR DVD/VCR VCR AUDIO OUT AUDIO IN VIDEO OUT VIDEO IN L ANT-IN ANT-OUT R L R Note to CATV system installer This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground should be connected to the grounding system of the building, as close to the point of cable entry as practical. CONNECTING TO A TV WITH A/V TERMINALS DVD/VCR VCR AUDIO OUT AUDIO IN L ANT-IN To VIDEO OUT jack To VIDEO INPUT jack To Right (red) and Left (white) Antenna/Cable signal To ANT. IN of TV To AUDIO INPUT jacks To AUDIO OUT jacks A/V-compatible or wide screen TV S-VIDEO OUT COMPONENT VIDEO OUT AUDIO OUT Y L R DIGITAL A...