valutazioni - 0, GPA: 0
(
)
)
|
da questo dispositivo ha anche altre istruzioni :
Facilità d'uso
• The video flash can only be used on a camcorder with the PHOTO recording function. As the brightness of the flash is automatically adjusted according to the distance of the subjects, your picture does not become whitish with too much brightness. Precautions Caution for heat Be careful not to touch the lighting section because the glass window and surrounding surfaces are hot while the light is on and just after it is turned off. • Never look directly at the bulb while the video light or flash is on. • Avoid placing the video flash light near combustible or volatile solvents such as alcohol or benzine. • Do not let any solid object or liquid fall onto or into the video flash light. • Do not knock or jolt the video flash light while it is turned on as it may damage or shorten the life of the bulb. • Do not leave the video light on while it is resting on or against something; it may cause a fire or damage the video flash light. • Do not pick up the camcorder by the head of the video flash light. • Remove the video flash light before putting the camera into a carrying case. • Do not place anything over the ventilation grill. • When the cover is hot do not allow it to get wet. • Do not leave the power switch of the video flash light on when it is not in use. • Do not turn the video flash light on without attaching the front cover. • If battery voltage drops to a certain level, the video flash light may not function suddenly. This is not a malfunction. In this case, turn off the power, then charge the battery pack again or use another fully charged battery pack. • When the front cover is hot, do not allow it to get wet. Otherwise, the video flash light may be damaged, or personal injury could result. • Do not place the video flash light in the following locations as it may be damaged or deformed: - extremely high temperature, such as in a car parked in the sun - directly in the sun, or near a heater - extreme vibration After use • Set the power switch to OFF. • Make sure the video flash light has cooled down before storing it. Be sure to remove the battery pack when the video flash light is not in use or stored in its case, etc. On cleaning Clean the video flash light with a dry soft cloth. You can remove stubborn stains with a cloth lightly dampened with a mild detergent solution, then dry the unit with a soft cloth. Never use strong solvents, such as thinner or benzine, since these will damage the finish on the surface. Specifications Video light segment Power requirements 6 V DC Lamp 5 W Maximum luminous intensity Approx. 200 cd Lighting direction Horizontal Lighting angle 20 degrees Continuous lighting time Type of battery pack Lighting duration NP-FF50 40 NP-FF70 90 (Approx. minutes using fully-charged battery pack) Illumination range Approx. 1 m (3 1/5 ft) 200 lux, Approx. 2 m (6 1/2 ft) 50 lux, Approx. 3 m (9 4/5 ft) 20 lux Color temperature 3 000 K Average life of bulb Approx. 100 hours Video flash segment Flash life Approx. 1 500 times Guide no. equivalent to 14 (Memory Photo recording) Color temperature 5 500 K Others Power consumption 5.5 W Dimensions Approx. 45 . 77 . 64 mm (excluding projecting (1 13/16 . 3 1/8 . 2 5/8 inches) parts) (w/h/d) Mass Approx. 100 g (3 1/2 oz.) Accessories (supplied) Shoe adapter (1) Operating instructions Accessory (not supplied) Halogen lamp XB-5DX Design and specifications are subject to change without notice. A Attaching the video flash light Set the power switch of the video flash light to OFF before attaching it to the shoe adapter or your camcorder. If your camcorder has the accessory shoe for the video flash light, attach the video flash light directly to the accessory shoe. Use the supplied shoe adapter when the accessory shoe is not provided on the camcorder. Using the shoe adapter 1 Attach the shoe adapter to the tripod receptacle of the camcorder. Turn the knob of the shoe adapter in the direction of the arrow to tighten firmly. A The guide marks to attach the camcorder to the shoe adapter. 2 Attach the video flash light to the shoe adapter. Make sure that the lighting section faces to the front and slide it firmly into the shoe adapter. You can turn the attached video flash light to the desired direction. Point the video flash light in the desired direction. Turn the lock knob in the direction of the arrow to tighten. B The point to adjust the direction of the video flash light. •Attach the video flash light in parallel with the camcorder when recording with the video flash. •Turn the video flash light to illuminate the central area of pictures when recording with the video light. 3 Connect the LANC cable. Connect the LANC cable of the video flash light to the LANC jack of the camcorder. Removing the video flash light 1 Set the power switch of the video flash light to OFF. 2 Remove the LANC cable from the LANC jack of the camcorder. 3 Loosen the lock knob by turning it in the direction of the arrow 1. 4 Remove the video flash light from the shoe adapter. 5 R...