valutazioni - 4, GPA: 4.3
(
)
)
|
Facilità d'uso
Repeat for other three legs. CHECK that all legs are securely attached to the motor housing by pulling firmly on them. Step 4. Open the swing legs completely. If necessary, turn legs to line up the dimples on the legs with the plastic leg braces. Snap leg braces onto outside of legs. The plastic pegs inside the ends of the braces will fit into the dimples on the legs. It may be necessary to spread the legs as shown. Do not use the swing without the leg braces. To close legs for storage, first unsnap leg braces. Then pull the tabs under the motor outward as shown, and move the legs inward. To remove legs completely, first move legs inward, then pull out with a twisting motion. Pull tabs Move legs End cap No wire Lower leg Wire Upper leg Lower leg Knob Wire Knob PUSH Peg SNAP Dimple 8 Step 3. From the inside of the seat, press the two plastic fasteners through the holes in the vinyl cover into the holes in the plastic seat. If holes in vinyl are not fully open, push fasteners through vinyl with enough force to open the holes. Step 4. Fold cover around bottom of seat. Cloth Seat Cover (on certain models): (No plastic fasteners are included with cloth seat cover models.) Step 1. Slide the pocket of the cloth cover over the top of the seat as shown. Step 2. Push both ends of the seat belt through the slots in the cloth cover, and pull the belt through. Step 3. Push the plastic clip under one side of the seat as shown. Repeat on other side. Step 4. Pull the fabric out at the leg openings. Step 1. Thread the free end of the seat belt through the belt retainer as shown. Step 2. Open buckle by squeezing sides of buckle to release. Step 3. Thread belt through the buckle as shown. CHECK to make sure that the belt is threaded correctly by pulling on the seat belt. The belt should not slip through the buckle. Vinyl Seat Cover (on certain models): Step 1. Slide pocket at top of vinyl seat cover over the seat back. Step 2. Push both ends of the seat belt through the slots in the vinyl cover, and pull the belt through. If slots in vinyl are not fully open, push ends of buckle through vinyl with enough force to open the slots. 7 Attaching the Seat Belt Attaching the Seat Cover—2 Options Your swing will have EITHER a vinyl or cloth seat cover. Follow the appropriate instructions below. Installing the Toy Bar Step 1. Place the two beads and three rings on the bar. The suggested order is ring-bead-ring-beadring. (Once the toy bar is on the tray, the order cannot be changed.) Step 2. Snap the bar (one end at a time) into the two “U”-shaped holes located on the top front of the tray. CHECK that bar is securely attached by pulling up on the bar. Step 3. Finished assembly will look like illustration. The seat has two positions, upright and reclined. T the seat wire, then pull the back of the seat downward. For the upright position, just pull forward on the top of the seat. bled before and during use. Do not tie other toys or objects onto the swing toys. If child is able to remove the toy bar from the tray Reclining the Seat Back Starting Swing Be sure all parts are securely fastened together before using the swing. Step 1. Open the seat belt. Place baby in the seat. (If your child is very small, you may want to use rolled-up blankets as a prop.) Step 2. Fasten the seat belt. Adjust belt as needed to get a snug fit around your child. Replacement Instructions Complete included Your swing Parts Motor Plastic Side-Side-Front-Vinyl Cloth Seat Hardware Plastic Adjustment Upper Lower Leg To * On Step 3. Wind crank clockwise. Swing is fully wound when you hear a clicking sound while winding. Step 4. PUSH SWING SEAT TO START. BE SURE YOU PUSH IT UP HIGH ENOUGH FOR THE MOTOR TO GET A GOOD START. Special features on certain models: Some models have a “time-remaining” indicator on the right side of the swing faceplate. After you finish winding, it will show you the remaining swing time. It also indicates when you need to rewind the motor. Some models have a switch on the left side of the swing faceplate to adjust the height of the swinging motion. Observe the swinging motion for a minute before changing the setting. It takes time for your swing to adjust to a new setting. • For a lower ride, push the control switch toward “low.” • For a higher ride, push the control switch toward “high.” NOTE: Seat may be stopped any time motor is running without damaging motor. To restart, push swing. 135-1-99 IS2132 9 10 Replacement Parts Instructions for ordering swing parts: Complete form below. Your swing model number MUST be included on the form to ensure proper replacement parts. Your model number can be found on a sticker beneath the swing motor. Payment must accompany your order. Parts List: Price:** Motor unit ..................................... $25.00 Plastic seat ................................... $21.00 Side-button hanger tube (right)* ... $13.00 Side-button hanger tube (left)* ..... $13.00 Front-button hanger tube* ............ $13.00 Vinyl s...