|
Facilità d'uso
and maximum of 14.0” w.c. In order to connect Propane, use a fitting with 1/2” NPT on the valve side and 1/2” propane gas sup- ply line with an input of 36,000 BTUs at a manifold pressure of 10.0” between a minimum inlet supply of 11.0” w.c. and maximum of 14.0” w.c. CAUTION Burner Information The appliance must only use the gas specified on the rating plate, unless converted using a Vermont Castings Fuel Conversion Kit. To convert from Natural Gas to LP use Kit 20012729 or 20012900. To convert from LP to Natural Gas use Kit 20012899 or 20012902. Conversion instructions are provided with each kit and beginning on Page 36 in this manual. 20012697 27 Radiance Direct Vent Gas Heater THIS APPLIANCE SHOULD BE CONNECTED TO THE GAS SUPPLY ONLY BY A QUALIFIED GAS SERVICE TECHNICIAN. FOLLOW ALL LOCAL CODES. THERE MUST BE A GAS SHUT-OFF BETWEEN THE STOVE AND THE SUPPLY. Install ON/OFF Switch The switch assembly parts are found in the parts bag. 1. Attach switch assembly to left rear side of stove shroud (when facing shroud) using two screws and existing holes in shroud. (Fig. 52) 2. Run wires down back of stove, under bottom of rear shroud to valve. 3. Attach wires to valve terminals. (Fig. 53) Switch As sembly Existing Holes Screws ST315 Fig. 52 Attach switch assembly to rear shroud. PILOTADJ TP THTPTH ST228 Fig. 53 Attach switch wires to valve. Thermostat Connection (optional) Use only a thermostat rated for 500 - 750 millivolts. Check the table below for the appropriate gauge thermostat wire to use for the length of lead required in your installation. Thermostat Wire / Gauge Maximum Run 18 20 feet 16 20 - 40 feet 14 up to 60 feet 1. Install the wall thermostat in the desired location and run the wires to the stove location. Terminate these leads with 1/4” female connectors. 2. Connect the thermostat wires to the valve. (Fig. 53) Install the Mesh and Grille Place the mesh and grille on the top of the Radiance stove to complete assembly. Operation ................ ........................................................................................................................................................................................ The Radiance is operated with the front plate in place with the doors open or closed. To open the front doors, pull forward to separate the magnetic catch. CAUTION: DO NOT TOUCH DOORS WHEN HOT! Your First Fire Read these instructions carefully and familiarize yourself with the burner controls shown on Page 29. Locate the pilot assembly, Figure 54. Follow the lighting instructions on Page 30 exactly. During the first fire, it is not unusual to smell some odor associated with new logs, paint and metal being heated. Odors should dissipate within the first eight to ten hours, however, you can open a window to provide fresh air to alleviate the condition. Pilot and Burner Inspection Each time you light your heater check that the pilot flame and burner flame patterns are as shown in Figure 56. If flame patterns are incorrect, turn the heater off. Contact your dealer or a qualified gas technician for assistance. Do not operate the heater until the pilot flame is correct. Radiance Direct Vent Gas Heater ST476 Pilot As- sembly Fig. 54 Pilot Assembly location. Follow regular maintenance procedures as described on Page 41. Flame & Temperature Adjustment For stoves equipped with HI/LO valves, flame adjustment is accomplished by rotating the HI/LO adjustment knob located near the center of the gas control valve. (Fig. 55) Turn LOHI Turn clockwise counterclockwise to decrease to increase flame height flame height Fig. 55 Flame adjustment knob for SIT valve. FP390 Flame Characteristics FLAME ADJUSTMENT KNOB It is important to periodically perform a visual check 11/21/96 of the pilot and the burner flames. Compare them to Figure 56. If any of the flames appear abnormal, call a service person. PSE Pilot RADVTC Series (Comfort Control Models) SIT Pilot RADVT Series CO105d LG491 Fig. 56 Correct pilot and burner flame appearance. 20012697 29 ......... ............... Radiance Direct Vent Gas Heater FOR YOUR SAFETY READ BEFORE LIGHTING • If you cannot reach your gas supplier, call the Fire Department C. Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, do not try to repair it, call a qualified service technician. Applying force or any attempted repair may result in a fire or explosion. D. Do not use this fireplace if any part has been under water. Immediately call a qualified service technician to inspect the heater and to replace any part of the control system and any gas control which has been under water. A. This heater has a pilot which must be lit manually. When lighting the pilot follow these instructions exactly. B. BEFORE LIGHTING smell all around the heater area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor. WHAT TO DO IF YOU SMELL GAS • Do not try to ...
Questo manuale è adatto anche per i modelli :Camini - RADVTSG (4.03 mb)
Camini - RADVTVG (4.03 mb)
Camini - RAD- VTBB (4.03 mb)
Camini - RADVTBD (4.03 mb)