Take out all the parts and compare them to the diagrams below. Be sure you have all the parts and can identify them. • A helping hand is always good. Assemble your mantel with an adult assistant if possible. Some pieces are heavy and will need to be held by a helper. Assembly time will take approximately 30-60 minutes. TOP 1PC ZZ.252AEE.01 BASE 1PC ZZ.252AEE.02 1 LEFT SIDE PANEL EXTERIOR 1PC ZZ.252AEE.03 LEFT SIDE PANEL INTERIOR 1PC ZZ.252AEE.04 RIGHT SIDE PANEL EXTERIOR 1PC ZZ.252AEE.05 RIGHT SIDE PANEL INTERIOR 1PC ZZ.252AEE.06 PANEL UNDERNEATH THE TOP 1PC ZZ.252AEE.07 CENTRAL TOP SHELF 1PC ZZ.252AEE.08 CENTRAL SHELF 1PC ZZ.252AEE.09 LEFT TOP SHELF 1PC ZZ.252AEE.10 RIGHT TOP SHELF 1PC ZZ.252AEE.11 LEFT BASE SHELF 1PC ZZ.252AEE.12 LEFT ADJUSTABLE SHELF 1PC ZZ.252AEE.13 RIGHT INTERIOR SHELF 1PC ZZ.252AEE.14 LEFT LOWER PANEL 1PC ZZ.252AEE.15 RIGHT LOWER PANEL 1PC ZZ.252AEE.16 CENTRAL PANEL 1PC ZZ.252AEE.17 LEFT BACK PANEL 1PC ZZ.252AEE.18 RIGHT BACK PANEL 1PC ZZ.252AEE.19 SPEAKER 2PCS ZZ.252AEE.20 LEFT DOOR 1PC ZZ.252AEE.21 RIGHT DOOR 1PC ZZ.252AEE.22 CENTRAL DOOR 1PC ZZ.252AEE.23 2PCS 2PCS 4PCS DOOR SUPPORTER 2PCS SHELF MOUNTING PEG 4PCS WING NUT 38PCS 21PCS 4PCS HARDWARE GET READY TO START Before assembly, use scissors to unwrap the parts from the packaging. DO NOT use a box cutter or exacto-knife as you may cut into the mantel pieces inside the box and damage the finish. Check for the hardware bag which is RED and located inside the packaging, taped to the top box. Be sure you DO NOT discard any pieces. Use an appropriate screwdriver to insert and tighten all screws. Step 1 Locate the base and place it on the floor. DO NOT put the base up against the wall at this point in the assembly. You need to get behind the mantel during the assembly process to insert and tighten several wing nuts, lock washers, hinges and screws. Step 2 Locate the left side panel (exterior) and position it on the left side (exterior) of the base. Line up the 2 holes, insert and tighten the 2 wing nuts and lock washers. Step 3 Locate the left back panel and slide it into the groove shown on the base and the left side panel. Locate the left lower panel. Insert the 2 dowels into the dowel holes located on the left side panel. Step 4 Locate the left side panel (interior) and position it on the left side (interior) of the base. Ensure the 2 dowels on the left lower panel insert into the 2 holes on the left side (interior). Line up the 2 holes between the base and the left side panel (interior), insert and tighten the 2 wing nuts and lock washers. 2 Step 5 Locate the left top shelf. Position it on the 4 supports on the left side panels – 2 on the exterior and 2 on the interior panels. From below line up the holes in the supports with those of the top shelf, insert and tighten the 4 wing nuts and lock washers. Step 6 Locate the central panel. Insert the 2 dowels on the cental panel into the dowel holes on the left side panel (interior) which are at the same level as the left lower panel. Step 7 Locate the right side panel (interior) and position it on the right side (interior) of the base. Insert the 2 dowels located on the right side of the left lower panel into the dowel holes on the right side panel (interior). Line up the holes on the right side panel (interior) and the base, insert and tighten the 2 wing nuts and lock washers. Step 8 Locate the central top shelf (with hinges) and set it on top of the left and right interior panels. From the top, line up the 4 holes (2 on each side), insert and tighten 4 wing nuts and lock washers. 3 Rear View Rear View Step 9 Locate the support panel for the top of the mantel. Insert the dowels on the side of the support panel into the dowels holes in the left side panel (exterior). Line up the support in the middle of the support panel with the hole in the central top shelf. From the top, insert and tighten the 1 wing nut and lock washer. Step 10 Locate the right lower panel, right interior shelf and the right back panel. Insert the dowels on the right lower panel into the dowel holes on the right interior side panel. Insert the dowels on the side of the right interior shelf into the dowels on the right interior side panel. Slide the right back panel into the groves on both the right interior shelf and the right interior side panel. Step 11 Locate the right top shelf and slide the shelf onto the supports located on the right interior side panel. Line up the holes, insert and tighten the 2 wing nut and lock washers. Step 12 Locate the right side panel (exterior) and position it on the right side (exterior) of the base. Ensure the 2 top supports go under the right top shelf. Ensure the 2 dowels on the support panel for the top of the mantel go into the dowel holes on the right exterior side panel. Ensure the dowels on the side of the right lower panel go into the holes on the right exterior side panel. Ensure the dowels on the side of the right interior shelf go into the holes on the right exterior sid...