valutazioni - 3, GPA: 3.7 ( )

Produttore : Regency File Size : 973.7 kb File Nome : Lingua di insegnamento:

Route Flex Vent Ensure that the flex vent is properly routed to provide the required clearance. Do Not allow the flexible vent to bend in a radius tighter than 5" (127 mm). Refer to Figure 43. Support horizontal sections of flex with metal straps at 2 foot (0.61 m) intervals. Step 4. FIELD WIRING Step 4. FIELD WIRING A. SIT and Honeywell Millivolt Wiring (See Figure 44 )– 1. Select any of the following optional controls: appliance-mounted (rocker switch) or wall-mounted switch, thermostat, or one of the optional remote control kits. If appliance- mounted ON/OFF control is selected mount it in the gas valve mounting bracket. 2. If wall-mounted ON/OFF control or thermostat is selected mount it in a convenient location on a wall near the fireplace. 3. Wire the control switch within the millivolt control circuit using the 15 feet of 2 conductor wire supplied with the unit. Caution: do not connect the optional wall switch to a 120V power supply. 4. Alternatively, the appliance may be operated without the use of the controls indicated in step 1, solely by manipulating the gas valve control knob. In order to use this method, twist the free ends of the two conductor wire (located inside the bottom compartment of the unit) together as shown in Figure 44. Note:The supplied 15 feet of 2 conductor wire has one end of each conductor connected to the gas valve circuit and the other end of each conductorplaced loose inside the bottom compartment of the unit. Figure 44 Millivolt Wiring Diagram If any of the original wire as supplied must be replaced, it must be replaced with Type AWM105°C – 18 GA. wire. Thermopile THTP TH TP *TWIST WIRES “A” AND “B” TOGETHER TO OPERATE UNIT SOLELY BY MANIPULATING THE GAS VALVE CONTROL KNOB; OR CONNECT WIRES TO OPTIONAL ON/OFF SWITCH OR WALL SWITCH OR THERMOSTAT TO OPERATE UNIT. *OPTIONAL ON/OFF SWITCH, WALL SWITCH, THERMOSTAT OR REMOTE CONTROL RECEIVER A B Note:The supplied 15 feet of 2 conductor wire has one end of each conductor connected to the gas valve circuit and the other end of each conductor placed loose inside the bottom compartment. B. Electronic Wiring (See Figure 45) – Note:The electronic appliance must be connected to the main power supply. 1. Route a 3-wire 120Vac 60Hz 1ph power supply to the appliance junction box. 2. Remove the outlet box from the junction box by removing two screws . 3. Connect the black power supply wire to the lower outlet's red pigtail lead and the white power supply wire to the common terminal of the outlet as shown in Figure 46. 4. Connect the ground supply wire to the outlet's green ground screw. 5. Locate and install a low voltage (24V) wall switch or thermostat (not supplied) in the desired location. 6. Connect the low voltage wire to this switch or thermostat. 7. Insert the control circuit plug into the lower outlet box. 8. After wiring is complete, replace the outlet box. Note:The gas valve-mounted ON/OFF switch is shown inFigure 45. It is integral with the gas valve. Step 5. WIRING - OPTIONAL FORCED AIR BLOWER KIT (See Figure 45 ) An electrical outlet box is provided for the installation of the FBK-100, FBK-200 forced air blower kits (optional). Electrical power must be provided to this box to operate these blowers. 1. Route a 3-wire, 120Vac 60Hz 1ph power line with control switch to the lower right rear corner of the appliance. 2. Remove the outlet box by removing two screws. 3. Connect the supply wires to the blower control switch. Then connect the wires from the blower control switch to the outlet box' pigtail leads as shown in Figure 45. NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 4. Connect the ground supply wire to the outlet's green ground screw. 5. Reinstall the outlet box. 6. Insert the blower pl...

Scarica la tua

Per scaricare, digitare 2 cifre :