Theinstallationmustconformwithlocalcodesor,intheabsenceof local codes, with the National Fuel Gas Code, ANSI Z223.1.* *Available from the American National Standards Institute, Inc. 1430 Broadway, New York, N.Y. 10018. High Altitudes Foraltitudes/elevations above2,000feet(610m),ratings shouldbe reduced at the rate of 4 percent for each 1,000 feet (305m) above sea level. Contact the manufacturer or your gas company before changing spud/orifice size. Well Head Gas Installations Some natural gas ut

— WHAT TO DO IF YOU SMELL GAS • Do not try to light any appliance. • Do not touch any electrical switch; do not use any phone in your building. • Immediately call your gas supplier from a neighbor'sphone. Followthegassupplier's instructions. • If you cannot reach your gas supplier, call the fire department. — Installation and service must be performed by a qualified installer, service agency or the gas supplier. WARNING: If the information in this manual is not followed exactly, a fire or explos

Consumer: Retain this manual for future reference. — Do not store or use gasoline or other flamma- ble vapors and liquids in the vicinity of this or any other appliance. — WHAT TO DO IF YOU SMELL GAS • Do not try to light any appliance. • Do not touch any electrical switch; do not use any phone in your building. • Immediately call your gas supplier from a neighbor’s phone. Follow the gas suppli- er’s instructions. • If you cannot reach your gas supplier, call the fire department. — Installation

NOT INTENDED FOR USE AS A PRIMARY HEAT SOURCE. This appliance is tested and approved as either supplemental room heat or as a decorative appliance. It should not be factored as primary heat in residential heating calculations. This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases, unless a certified kit is used. The Keystone "B" Vent Zero Clearance Gas Fireplace WARNING: If the information in this manual is n

Therefore, people should be particularly alert and careful when new tanks or cylinders are placed in service. Odor fade can occur in new tanks, or reinstalled old tanks, if they are filled and allowed to set too long before refilling. Cylinders and tanks which have been out of service for a time may develop internal rust which will cause odor fade. If such conditions are suspected to exist, a periodic sniff test of the gas is advisable. If you have any question about the gas odor, call your LP-G

These include the vent system, gas piping for the appliance, Fresh Air Kit, and the electrical wiring. (The fan option is available for louvered models only. Electric ignition models will require electrical service to junction box). The appliance can be mounted on any of the following surfaces: 1. A flat, hard combustible (burnable) surface. 2. A raised wooden platform. 3. Four (4) corner supports. (Example: Four (4) concrete masonry blocks.) These supports must be positioned so they contact all

b. Debris around throat of main burner. —Inspect the opening at the base of the main burner. It is imperative that NO material be placed in this opening. Page 20 19400-3-0406 STANDING PILOT PROPANE/LP GAS CONVERSION "B-VENT" FIREPLACES Model Conversion Kit Model (Part Number) BVD34FP3 SERIES BVCK34P (19160) BVD36FP3 SERIES BVCK36P (19161) BVP42FP3 SERIES BVCK42P (19162) FOR CONVERSION TO LIQUEFIED PETROLEUM GAS WARNING This conversion kit is to be installed by an Empire Comfort Systems, Inc. dea

3. Connect female terminal from receiver onto 120 VAC hot terminal on control module. 4. Connect remaining wire from remote control (male terminal) to (female terminal) on power cord removed from control module (step 2). 5. Insert electric remote control power cord plug into the junction box on the right side of fireplace. 6. Connect 3-prong plug into receptacle. See wiring diagram on page 34. Figure 24 DIRECT IGNITION WIRING DIAGRAM OPTIONAL REMOTE CONTROL (120V DIRECT IGNITION) Page 24 19400-3

2. Care must be taken to avoid breakage of glass. 3. Do not abuse the glass by striking or hitting the glass. WARNING: Do not use abrasive cleaners on glass. Do not attempt to clean glass when glass is hot. 19400-3-0406 Page 27 BVD34 & BVD36 PARTS LIST INDEX NO. PART NUMBER DESCRIPTION BVD34L BVD34F BVD36L BVD36F 1 19506 19506 19507 19507 TOP SHIELD 2 17301 17301 17301 17301 TOP STANDOFF (2 REQUIRED) 3 10554 10554 10554 10554 NAILING FLANGE (4 REQUIRED) 4 M163 M163 M178 M178 FLUE OUTLET GASKET 5

• Do not use the phone in your building. • Immediately call your gas supplier from a neighbor's phone. • Follow the gas supplier's instructions. • If you cannot reach your gas supplier, call the fire department. INSTALLATION INSTRUCTIONS AND OWNER'S MANUAL CAST IRON VENTED FIREPLACE HEATER MODEL CIBV-30-2 EFFECTIVE DATE APRIL, 2000 WARNING: If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or loss of life. Installat