valutazioni - 2, GPA: 4
(
)
)
|
Facilità d'uso
f Rotate the hinge body 180 degrees so that the hinge-pin holes are now on the right side of the hinge body (see Figure 1-7). Installation Guide Figure 1-7. Reversing the Top and Bottom Hinges 2 3 4 1 5 6 7 1 hinge pin 2 top hinge body 3 spring 4 retention clip 5 hinge post 6 bottom hinge body 7 front of rack Installation Guide g Locate the top bolt holes in the right side of the rack, and fasten the hinge body to the right side of the rack with the Allen bolts. h Insert the spring between the top and bottom hinge-pin holes in the bottom hinge body. i Slide the hinge pin into the hinge body. j Insert the retention clip through the hinge so that the retention clip is below the spring. 4 Reverse the bottom hinge body. a Remove the Allen bolts that secure the hinge body to the rack, and place the bolts in a safe location. b Rotate the hinge body 180 degrees so that the hinge posts are now on the other side of the hinge body (see Figure 1-7). c Locate the bottom bolt holes in the right side of the rack, and use the Allen bolts to fasten the hinge body to the right side of the rack. 5 Rotate the front door 180 degrees so that its hinge-pin housings are on the right side (see Figure 1-8). Installation Guide Figure 1-8. Rotate the Front Door 6 Rehang the front door by reversing the steps in "Removing the Front Door" on page 8. 7 Reverse the lock catch. a Unscrew the two Phillips screws that hold the lock catch to the vertical frame member. b Remove the lock catch and rotate it 180 degrees. c Reinstall the lock catch on the other rack front vertical frame member by aligning the holes of the catch with the holes of the frame member and then reinserting the two Phillips screws. See Figure 1-9. Installation Guide Figure 1-9. Reversing the Front Door Lock Catch 2 1 1 lock catch 2 screws 8 Reverse the badge on the front door. a Open the front door. b From inside the door, insert a flat-head screwdriver into the badge release notch (see Figure 1-10). Installation Guide Installation Guide 21 Figure 1-10. Reversing the Front Door Badge c Push the screwdriver into the notch until it stops and turn it counter-clockwise. d Lift up on the badge and pull it off the door. e Rotate the badge 180 degrees so that it will read correctly when reinstalled. 1 badge release notch 2 front door badge 3 center tab (2) 4 badge retention clip (2) 5 badge hook (2) 1 3 2 5 4 f Locate the sixth horizontal bar from the top of the door and slide the badge hooks over it, aligning the center tabs on the badge with the vertical bar on the door. g Push up on the badge retention clips until they are closed and the badge is secure. Securing the Rack Leveling Feet WARNING: Read all statements below before you adjust the leveling feet. Your rack includes four leveling feet, which are mounted on the corners of the rack. The leveling feet are designed to align the rack in an upright, level position when the rack is situated on a slightly uneven floor surface. Before you install your systems in the rack, deploy and adjust the leveling feet. When you level your rack, follow these guidelines. WARNING: When you adjust the leveling feet, ensure that the casters on each corner of the rack do not rise more than 9.5 mm (3/8 inch) above the floor. If you exceed 9.5 mm of clearance between the floor and the casters as you adjust the leveling feet, slowly retract the leveling feet, and then move the rack to another location that requires minimal adjustments to the leveling feet. WARNING: Adjust the leveling feet until each leveling foot rests firmly on the floor. Proper contact with the floor ensures that each leveling foot is supporting the weight of the rack and prevents the rack from swaying in any direction. If the leveling feet are not all in firm contact with the floor, the rack can become unstable and tip over. WARNING: Do not attempt to move your rack with the leveling feet deployed. Always retract the leveling feet before moving the rack. Having the leveling feet deployed when you move the rack may cause the rack to tip over. WARNING: Always level the rack and install the stabilizing feet before you install your systems. A fully loaded rack may tip over if your rack is resting on an uneven floor surface and the leveling and stabilizing feet are not supporting the weight of the rack. NOTE: If the rack is not leveled properly, you might not be able to install the stabilizer feet, which are necessary to prevent the rack from tipping over. Installation Guide 1 Using a screwdriver, lower the leveling foot until it rests on the floor. 2 If you need to lower the foot further, tighten the hex nut clockwise with a 12-mm wrench (see Figure 1-11). 3 Repeat steps 1 and 2 for the remaining leveling feet. 4 Ensure that the rack is level. Figure 1-11. Adjusting the Leveling Feet 3 1 2 1 leveling foot stem 2 hex nut 3 leveling pad Installation Guide Installing the Rack Stabilizer Feet WARNING: Installing systems in a rack without the front and side stabilizer feet installed...
Questo manuale è adatto anche per i modelli :Computer - PowerEdge 21DXJ (4.27 mb)