valutazioni - 4, GPA: 3.8
(
)
)
|
Facilità d'uso
2 Swing the bottom of the panel downward onto the rack. 3 Press the panel into the rack until both latches lock into place. Installation Guide Figure 1-4. Replacing the Upper Side Panels 2 3 1 1 panel lip 2 upper side panel (2) 3 latches (2) Removing the Lower Side Panels 1 Pull both latches down and allow the side panel to swing outward slightly at the top. 2 Firmly grasp both sides of the panel. 3 Lift the panel upward until the panel hooks clear the holes in the bottom of the rack frame. 4 Place the panel in a safe location with the panel’s outer surface facing upward to help prevent damage to its cosmetic coating. 5 Repeat step 1 through step 4 for the other lower side panel. Installation Guide Replacing the Lower Side Panels 1 Lower the panel into the rack, inserting the back panel hook into the back hole in the bottom of the rack frame and the front hook into the corresponding hole in the front of the rack frame (see Figure 1-5). 2 Swing the top end of the panel towards the rack. 3 Press the panel into the rack until both latches lock into place. Figure 1-5. Replacing the Lower Side Panels 1 2 3 1 panel hook (2) 2 latch (2) 3 lower side panel (2) Installation Guide Reversing the Front Door (optional) NOTE: Use a 4-mm Allen wrench to remove the front-door hinge bodies from the rack and reinstall them on the side opposite their original positions. You might need a stepladder in order to access the Allen bolt that secures the top hinge body to the rack. To reverse the direction that the front door opens, complete the following steps: 1 Remove the front door (see "Removing the Front Door" on page 8). 2 Remove the side panels (see "Removing and Replacing the Side Panels" on page 12). 3 Reverse the top hinge body. a Pull the hinge pin upward slightly so that you can access the retention clip (see Figure 1-6). b Using the needle-nose pliers, remove the retention clip, and slide the hinge pin out of the hinge body. Installation Guide Figure 1-6. Removing the Front-Door Hinges 1 6 5 2 3 4 1 hinge pin 2 top hinge body 3 bottom hinge 4 hinge post 5 retention clip 6 body spring c Remove the hinge spring from the hinge body. d Place the hinge pin, retention clip, and spring in a safe location. e Using the 4-mm Allen wrench, remove the Allen bolts that secure the hinge body to the rack, and place the bolts with the hinge pin, retention clip, and body spring. f Rotate the hinge body 180 degrees so that the hinge-pin holes are now on the right side of the hinge body (see Figure 1-7). Installation Guide Figure 1-7. Reversing the Top and Bottom Hinges 2 3 4 1 5 6 7 1 hinge pin 2 top hinge body 3 spring 4 retention clip 5 hinge post 6 bottom hinge body 7 front of rack Installation Guide g Locate the top bolt holes in the right side of the rack, and fasten the hinge body to the right side of the rack with the Allen bolts. h Insert the spring between the top and bottom hinge-pin holes in the bottom hinge body. i Slide the hinge pin into the hinge body. j Insert the retention clip through the hinge so that the retention clip is below the spring. 4 Reverse the bottom hinge body. a Remove the Allen bolts that secure the hinge body to the rack, and place the bolts in a safe location. b Rotate the hinge body 180 degrees so that the hinge posts are now on the other side of the hinge body (see Figure 1-7). c Locate the bottom bolt holes in the right side of the rack, and use the Allen bolts to fasten the hinge body to the right side of the rack. 5 Rotate the front door 180 degrees so that its hinge-pin housings are on the right side (see Figure 1-8). Installation Guide Figure 1-8. Rotate the Front Door 6 Rehang the front door by reversing the steps in "Removing the Front Door" on page 8. 7 Reverse the lock catch. a Unscrew the two Phillips screws that hold the lock catch to the vertical frame member. b Remove the lock catch and rotate it 180 degrees. c Reinstall the lock catch on the other rack front vertical frame member by aligning the holes of the catch with the holes of the frame member and then reinserting the two Phillips screws. See Figure 1-9. Installation Guide Figure 1-9. Reversing the Front Door Lock Catch 2 1 1 lock catch 2 screws 8 Reverse the badge on the front door. a Open the front door. b From inside the door, insert a flat-head screwdriver into the badge release notch (see Figure 1-10). Installation Guide Installation Guide 21 Figure 1-10. Reversing the Front Door Badge c Push the screwdriver into the notch until it stops and turn it counter-clockwise. d Lift up on the badge and pull it off the door. e Rotate the badge 180 degrees so that it will read correctly when reinstalled. 1 badge release notch 2 front door badge 3 center tab (2) 4 badge retention clip (2) 5 badge hook (2) 1 3 2 5 4 f Locate the sixth horizontal bar from the top of the door and slide the badge hooks over it, aligning the center tabs on the badge with the vertical bar on the door. g Push up on the badge retention clips until they are close...
Questo manuale è adatto anche per i modelli :Computer - PowerEdge 4820 (4.27 mb)