valutazioni - 1, GPA: 3 ( )

Produttore : Acer File Size : 375.02 kb File Nome : Lingua di insegnamento:

Connecting peripherals After everything is connected, plug the power cord into the system and insert the other end into a power outlet. Note: Don't connect the system power cord before connecting all peripherals to the system. Starting your computer After connecting all the peripheral equipment, start your computer according to the steps below: 1 Turn on all peripheral equipment, such as the monitor, printer, fax, speakers, etc. 2 Turn on the system. Once the start up process is complete, you can begin to use your computer. Shutting down your computer From the "Start" menu, select "Shut Down" and click OK. In the event of a system crash, press and hold the power button on the front of the system for four seconds. After the system has shut down, turn off all peripheral devices. English EnglishEnglish 6 Setting up your computer System upgrade You can expand your AcerPower series system quickly and easily by adding components. You can also upgrade the components of your AcerPower series system. Opening the computer Before removing any panels or covers, please make sure to shut off the computer and unplug the power cord from the outlet. • Remove the two screws on the side panel. • Slide the panel back and off. Setting up new components You can only use components compatible with AcerPower series computers. Before you choose new components, please ask your authorized Acer dealer whether the part will operate within your AcerPower series system. In order to ensure proper setup and installation, please refer to the instructions provided with your new components. Probable upgrades are: -Upgrade to high-capacity HDD -Expand high-level memory -Upgrade from a CD-ROM drive to CD-RW, DVD-ROM, DVD/CD-RW combo or DVD writer -Install additional interface cards in empty PCI slots, e.g., PCI fax/modem card 7 Troubleshooting The following are possible situations that may arise during the use of your computer, and each is followed by simple answers and solutions. Q: I pressed the power switch but the system did not boot up. A: Check the LED located above the power switch. If the LED is not lit, no power is being applied to the system. Do any of the following: • Check if the voltage selector switch located on the rear panel of the computer is set to the correct voltage. • Check if you have properly plugged the power cable into an electrical outlet. • If you are using a power strip or AVR, make sure it is plugged in and turned on. If the LED is lit, check the following: • Is a non-bootable (non-system) floppy disk in the floppy drive? If yes, remove or replace it with a system floppy disk and press + + to restart your computer. Q: Nothing appears on the screen. A: Your computer's power management function automatically blanks the screen to save power. Press any key to turn the display back on. If pressing a key does not work, restart your computer. If restarting your computer does not work, contact your dealer or the technical support center for assistance. Q: The printer does not work. A: Do the following: • Make sure the printer is connected to a power outlet and that it is turned on. • Make sure the printer cable is connected securely to the system's parallel port and the corresponding port on the printer. • For additional information concerning the printer, refer to the printer's documentation. Q: No sound comes out of the speakers. English EnglishEnglish 8 Troubleshooting A: Check the following: • The volume may be muted. Look for the Volume icon on the taskbar. If it is crossed-out, click on the icon and deselect the mute option. You can also press the volume control/mute knob on your USB keyboard to toggle the mute function. • If headphones, earphones or external speakers are connected to the line-out jack of your computer, the internal or built-in speakers are automatically turned off. Q: System cannot read floppy disk, hard disk, CD or DVD information. A: Check the following: • Make sure you are using the correct type of media. • Check if the floppy disk is formatted correctly. If not, format it again. Caution: If you reformat a floppy disk, you will lose all data on it. Make sure the floppy disk, CD or DVD is inserted correctly (rightside up) into the proper drive (floppy disk goes into floppy drive, DVD goes into DVD drive). • Check to be sure the CD or DVD is clean and unscratched. • Check your drive by using a good (undamaged) floppy or optical disk. If your floppy, CD or DVD drive cannot read the information on the good floppy disk, CD or DVD, there may be a problem with the drive. Contact your dealer or technical support center for assistance. Q: System cannot write to floppy disk, hard disk or optical disk. A: Check the following: • Make sure the media is not write-protected. • Make sure you are using the correct type of floppy disk. Check if the floppy disk is formatted correctly. If not, format it again. Caution: If you reformat a floppy disk, you will lose all data on it. 9 Taking care of yo...

Scarica la tua

Per scaricare, digitare 2 cifre :