valutazioni - 4, GPA: 3.5
(
)
)
|
Facilità d'uso
Force BIOS recovery setting (3-pin RECOVERY1) This jumper allows you to quickly update or recover the BIOS when it gets corrupted. ® P5BP-E/4LP5BP-E/4L BIOS Recovery SettingRECOVERY1(Default) NormalBIOS recovery2321 To update the BIOS 1. Prepare a floppy disk that contains the latest BIOS for the motherboard (xxxx-xxx.ROM) and the AFUDOS.EXE utility. 2. Set the jumper to pins 2-3. 3. Insert the floppy disk then turn on the system to update the BIOS. 4. Shut down the system. 5. Set the jumper back to pins 1-2. 6. Turn on the system. ® P5BP-E/4L1212CPUFAN_SET1(Default) PWM ModeDC Mode23CHAFAN_SET1(Default) PWM ModeDC Mode23P5BP-E/4L Fan Mode Setting 4. Fan mode setting (3-pin CPUFAN_SET1 and CHAFAN_SET1) These jumpers allow you to connect either a 3-pin or a 4-pin fan cable plug to the CPU fan or Chasis fan connectors Set these jumpers to pins 1-2 Short PWM mode if you are using a 4-pin fan cable plug, or to pins 2.3 Short DC mode if you are using a 3-pin plug. 4.3 Connectors 4.3.1 Rear panel connectors 18564327 1. PS/2 mouse port (green). This port is for a PS/2 mouse. 2. LAN port. This port is for upcoming ASMB3-iKVM controller card only and does not support common network connections.. 3. Dual integrated Gigabit Ethernet connections LAN1_LAN2. These ports allow Gigabit connection to a Local Area Network (LAN) through a network hub. (The bottom one is LAN1.) Refer to the table below for the LAN port LED indications. 4. Dual integrated Gigabit Ethernet connections LAN3_LAN4. These ports allow Gigabit connection to a Local Area Network (LAN) through a network hub. (The bottom one is LAN3.) Refer to the table below for the LAN port LED indications. 5. VGA port. This port is for a VGA monitor or other VGA-compatible devices. 6. Serial (COM1) port. This 9-pin communication port is for pointing devices or other serial devices. 7. USB 2.0 ports 1 and 2. These two 4-pin Universal Serial Bus (USB) ports are available for connecting USB 2.0 devices. 8. PS/2 keyboard port (purple). This port is for a PS/2 keyboard. LAN port LED indications SPEED LED ACT/LINK LED Activity/Link LED Speed LED Status Description Status Description OFF No link OFF 10 Mbps connection ORANGE Linked ORANGE 100 Mbps connection BLINKING Data activity GREEN 1 Gbps connection LAN port 4.3.2 Internal connectors 1. Floppy disk drive connector (34-1 pin FLOPPY1) This connector is for the provided Floppy Disk Drive (FDD) signal cable. Insert one end of the cable to this connector, then connect the other end to the signal connector at the back of the floppy disk drive. ® P5BP-E/4LP5BP-E/4L Floppy Disk Drive ConnectorNOTE:Orient theredmarkingsonthe floppy ribbon cable to PIN 1. PIN1FLOPPY Pin 5 on the connector is removed to prevent incorrect cable connection when using a FDD cable with a covered Pin 5. 2. ICH7R Primary IDE connector (40-1 pin PRI_IDE1) The onboard IDE connector is for the Ultra DMA 133/100 signal cable. There are three connectors on each Ultra DMA 133/100 signal cable: blue, black, and gray. Connect the blue connector to the motherboard’s IDE connector, then select one of the following modes to configure your device. ® P5BP-E/4LP5BP-E/4L IDE ConnectorNOTE:Orient the red markings(usually zigzag) on the IDEribbon cable to PIN 1. PRI_IDE1PIN 1 Drive jumper setting Mode of device(s) Cable connector Single device Cable-Select or Master - Black Two devices Cable-Select Master Black Slave Gray Master Master Black or gray Slave Slave • Pin 20 on the IDE connector is removed to match the covered hole on the Ultra ATA cable connector. This prevents incorrect insertion when you connect the IDE cable. • Use the 80-conductor IDE cable for Ultra ATA 100/66/33 IDE devices. If any device jumper is set as “Cable-Select,” make sure all other device jumpers have the same setting. 3. Serial ATA connectors (7-pin SATA1-4) These connectors are for the Serial ATA signal cables for Serial ATA hard disk drives. If you installed Serial ATA hard disk drives, you can create a RAID 0, RAID 1, RAID 10 and RAID 5 configuration using the Intel® Matrix Storage Technology or RAID 0, RAID 1 and RAID 10 configuration using the LSI MegaRAID® utility embedded in the Intel® ICH7R Southbridge. ® P5BP-E/4LP5BP-E/4L SATA ConnectorsSATA1SATA3SATA2SATA4GNDRSATA_TXP1RSATA_TXN1GNDRSATA_RXP1RSATA_RXN1GNDGNDRSATA_TXP2RSATA_TXN2GNDRSATA_RXP2RSATA_RXN2GNDGNDRSATA_TXP3RSATA_TXN3GNDRSATA_RXP3RSATA_RXN3GNDGNDRSATA_TXP4RSATA_TXN4GNDRSATA_RXP4RSATA_RXN4GND These connectors are set IDE mode by default. In IDE mode, you can connect Serial ATA boot/data hard disk drives to these connectors. If you intend to create a Serial ATA RAID set using these connectors, set the Configure SATA as item in the BIOS to [RAID]. See section 4.3.4 IDE Configuration for details. • Use only two Serial ATA RAID connectors for each RAID 0 or RAID 1 set. • When using the connectors in IDE mode, connect the primary (boot) hard disk drive to the SATA1 or SATA2 connector. Refer to the table below for the recommended ...