Purge Non-Condensibles. Each of the above steps is discussed in detail in this instruction. Read entire instruction before starting installation. Remove four shipping bolts holding absorption unit to crate base before placing unit on permanent mounting slab. NOTE: Unit is shipped with condenser fan guard inverted. Remove, place with convex side up and fasten. I. LOCATE AND MOUNTABSORPTION UNIT The absorption unit may be located at ground level or on the roof. Consult local codes for informa

The 550A family has been designed utilizing Bryant’s Puron refrigerant. The environmentally sound refrigerant allows you to make a responsible decision in the protection of the earth’s ozone layer. Bryant’s 550A system meets the Energy Star® guidelines for energy efficiency. FEATURES Puron Environmentally Sound Refrigerant—Is Bryant’s refrigerant designed to help protect the environment. Puron is an HFC refrigerant which does not contain chlorine that can harm the ozone layer. The most important

ALWAYS STORE THE UNIT UPRIGHT IN ORDER TO MAINTAIN THE COMPRESSOR IN A PROPER CONDITION. 5. BE SURE TO UNPLUG THE UNIT BEFORE CLEANING. 6. THE HEATER MUST NOT BE LOCATED IMMEDIATELY BELOW A SOCKET OUTLET. 7. IF THE APPLIANCE IS COVERED, THERE IS A RISK OF OVERHEAT. 8. IF THE SUPPLY TOOL OF THIS APPLIANCE IS DAMAGED, IT MUST BE REPLACED BY A REPAIR SHOP APPOINTED BY THE MANUFACTURER, BECAUSE SPECIAL PURPOSE TOOLS ARE REQUIRED. NOTE: The air-conditioner can be connected only to a supply with syste

No. Motormaster® I Control 036-150 13 Motormaster II Control 036-072 14 090-150 15 Time Guard® II Device 036-150 16 Solid-State Enthalpy Control 036-150 17 Differential Enthalpy Control 036-150 18 EconoMi$er 036-072 19 EconoMi$er Sensor Wiring 036-150 20 Power Exhaust 036-072 21 LEGEND AHA — Adjustable Heat Anticipator IFR — Indoor-Fan Relay TDR — Time-Delay Relay AWG — American Wire Gage LPS — Low-Pressure Switch TH — Thermostat, Heating C— Contactor, Compressor LSM — Limit Switch (Manual Reset

Instant mount models are designed for Windows 27.5 inch (699mm) to 36 inch (914mm) wide. 3. Mark the center of Window sill with pencil. 4. Insert Screws (Type A) into the sill bracket. 5. Attach Sill bracket to window sill using two Screws (Type B) by each bracket. The outside edge of window bracket should be 11.8 inch (300mm) from center line. 6. Adjust Screw (Type A) so that Sill Bracket have a slight tilt by using carpenter's level meter. Window Shutter (2 pieces) Window kit FrameLeft side (1

To install or replace batteries: 1. Slide the back cover off the control to open the battery compartment. 2. Insert batteries. Follow the polarity markings inside the battery compartment. 3. Replace battery compartment cover. NOTE: 1. When replacing batteries, do not use old batteries or a different type battery. This may cause the remote control to malfunction. 2. If the remote is not going to be used for several weeks, remove the batteries. Otherwise battery leakage may damage the remote contr

The qualified installer or agency must use factory- --authorized kits or accessories when modifying this product. Refer to the individual instructions packaged with the kits or accessories when installing. Follow all safety codes. Wear safety glasses, protective clothing, and work gloves. Use quenching cloth for brazing operations. Have fire extinguisher available. Read these instructions thoroughly and follow all warnings or cautions included in literature and attached to the unit. Consult loca

After a few minutes of operation, you should be able to see water trickle from the condensate drain of the cooling coil. Check this occasionally to be sure the drain system is not clogged. Of course, don’t expect to see much drainage if you live in a very dry environment. REGULAR DEALER MAINTENANCE In addition to the routine maintenance that you perform, your home comfort system should be inspected regularly by a properly trained service technician. The inspection (preferably each year, but at

This low-ambient control shall regulate speed of the condenser-fan motors in response to the saturated condensing temperature of the unit. The control shall maintain correct condensing pressure at outdoor temperatures down to –20 F. 2. Gage Panel Package: Gage panel package shall include a suction and discharge pressure gage. 569D072- 120, 576C120, 569F120 31 569D072- 120, 576C120, 569F120 569D072- 120, 576C120, 569F120 GUIDE SPECIFICATIONS — 569F120 (cont) 3. Optional Condenser Coil Materials:

317 240 5662 P. 001/001 PRODUCT DATA ELECTRONIC CONTROL OPTIONS AND FIA COMPONENTS These electronic pilot options are available for Model 246 Gas-Fired Boiler application. FIA does not approve a specific device or unit. Approval applies to the complete installation based upon the locai FIA engineer's evaluation ' of equipment, hazards of building usage, and the insurance liabilities involved, FIA generally recommends that gas-fired sectional boilers be equipped with electronically supervised