valutazioni - 1, GPA: 3
(
)
)
|
Foto e specifiche Panasonic ES-LA63 |
Facilità d'uso
Trimmer handle E Adaptor (RE7.51) . Power cord . Appliance plug F Soft case G Cleaning brush H Oil Charging Charge 1 Insert the appliance plug into the shaver. 2 Plug in the adaptor into a household outlet. The indicators on the LCD panel glow and charging starts. Charging is completed when the indicators on the LCD panel blink. (Max. 1 hour later) • • You cannot operate the shaver while charging. . . . ES-LA63_CIS.indb 3 2010/01/06 9:50:47 English About the LCD panel The LCD panel shows the remaining battery capacity from 0% to 100%, in 10% increments. While charging After charging is completed 10 minutes after charging is completed The indicators glow. The indicators blink once every second. The indicators blink once every 2 seconds. During use After use min.used min.used The used time is shown. The indicators turn off after 5 seconds. The shown time returns to [0’00”] after 10 minutes. •• The used time and the remaining battery capacity are shown alternately after turning off the shaver. When the battery capacity is low You can shave 1 to 2 times after “10%” appears. (This will differ depending on usage.) • “10%” appears and blinks. A full charge will supply enough power for approx. 14 shaves of 3 minutes each. • Using the shaver Shave 90° 1 Slide the switch lock button downwards and press the OFF/ ON switch. 2 Hold the shaver as illustrated above and shave. Start out shaving by applying gentle pressure to your face. Stretch your skin with your free hand and move the shaver back and forth in the direction of your beard. You may gently increase the amount of pressure as your skin becomes accustomed to this shaver. Applying excessive pressure does not provide a closer shave. Using the trimmer handle You can change the pivot action. Also, slide the handle up to “ ” when using the trimmer. FREE You can move the shaver head. LOCK FREE LOCK You can lock the shaver head. Slide the trimmer handle up. Place at a right angle to your skin and move downwards to trim your sideburns. FREE LOCK . ES-LA63_CIS.indb 4 2010/01/06 9:50:47 English Cleaning Clean We recommend that you clean your shaver with the turbo mode for “sonic” vibration cleaning when the faucet symbol appears on the LCD panel. 1. Disconnect the power cord from the shaver. 2. Apply some hand soap and some water to the outer foil. 3. Slide the switch lock button downwards to unlock the OFF/ ON switch. 4. Press the OFF/ON switch for more than 2 seconds to activate the turbo mode for “sonic” vibration cleaning. appears on the LCD panel. After about 20 seconds, it will be automatically turned off, or you can turn it off by pressing the OFF/ON switch. 5. Remove the outer foil section and press the OFF/ON switch for more than 2 seconds to activate the turbo mode for “sonic” vibration cleaning and clean it with running water. 6. Wipe off any drops of water with a dry cloth. • • 7 7. Dry the outer foil section and the shaver completely. 8. Attach the outer foil section to the shaver. 9. Lubricate the shaver. Caution for turbo mode Shaving in turbo mode may damage your skin. Turn the shaver off and then on again to cancel turbo mode. Do not place your fingers on the OFF/ON switch while using the shaver. This may cause the shaver to turn off or enter turbo mode. • • Lubrication To maintain shaving comfort for a long time, it is recommended that the oil provided with the shaver is used. 1. Switch off the shaver. 2. Apply one drop of oil to each of the outer foils. 3. Raise the trimmer and apply a drop of oil. 4. Switch the shaver on, and run it for approximately five seconds. 5. Switch off the shaver, and wipe off any excess oil from the outer foils with a soft cloth. ES-LA63_CIS.indb 5 2010/01/06 9:50:48 English Replacing the system outer foil and the inner blades appears on the LCD panel once a year. (This will differ depending on usage.) We recommend checking the system outer foil and the inner blades when it appears. Press the OFF/ON switch for more than 30 seconds to delete . system outer foil once every year inner blade once every two years Replacing the system outer foil 1. Press the foil frame release buttons and lift the outer foil section upwards as illustrated. 2. Press the system outer foil release buttons and pull down the system outer foil as illustrated. 3. Align the foil frame mark and the system outer foil mark and securely attach together. The system outer foil cannot be reversely attached. Always insert the system outer foil to the foil frame when attaching to the shaver. 4. After turning the mark to the front, securely attach the outer foil section to the shaver until it clicks. • 2 3 • • . Replacing the inner blades 1. Press the foil frame release buttons and lift the outer foil section upwards as illustrated. 2. Remove the inner blades one at a time as illustrated. Do not touch the edges (metal parts) of the inner blades to prevent injury to your hand. 3. Insert the inner blades one at a time until they click as illustrated. • 2 3 Cleaning wi...