valutazioni - 1, GPA: 3
(
)
)
|
Facilità d'uso
2002) Installation, Operation and Care of 4732 & 4732A CHOPPERS SAVE THESE INSTRUCTIONS GENERAL The 4732 and 4732A Choppers are equipped with a 3 HP motor that rotates the worm at 151 RPM. The 4732 and 4732A are designed to use a #32 size knife and plate. Knives and plates, available at extra cost, are not included with the chopper. The stainless steel feed pan on the 4732 is not removable and must be cleaned in place. Model 4732A has a removable stainless steel feed pan and an interlock that requires the feed pan to be in place before the machine can be turned on. On both models, a cast aluminum guard is permanently mounted to the front and sides of the feed pan. Dimensions on the feed pan are 34" long x 21" wide x 5" deep. The motor and switch housing is available in painted steel or stainless steel. The table models use 53/8" high legs that provide 8" clearance between the table and the lowest point on the adjusting ring. Leg sets of other heights (15", 18" or 21") are available to convert the 4732 or 4732A into a floor model. Sausage stuffers for hog or sheep casings are available accessories. The chopper can grind 35 to 40 pounds of boneless beef per minute, first cut, through a 1/8" plate. The second cut grind rate is 25 to 30 pounds per minute through a 1/8" plate. Frozen meat must be tempered to 24OF or higher before grinding and can be in either flake or stick form. INSTALLATION UNPACKING Immediately after unpacking, check for possible shipping damage. If the chopper is found to be damaged, save the packaging material and contact the carrier within 15 days of delivery. Remove the carton from around the machine. Remove the four bolts holding the machine to the skid. Unpack the feed stomper. Prior to installation, verify that the electrical service agrees with the specifications on the machine data plate. Use the spanner wrench to loosen the adjusting ring. Unscrew and remove the adjusting ring using both hands. Remove and discard the retaining washer and rubber pad used at the front of the worm where the knife and plate are to be installed. The chopper must be thoroughly cleaned and sanitized after installation and before operation. Refer to CLEANING (page 7). © HOBART CORPORATION, 2002 – 2 – Fig. 1 Fig. 1 LEGS (Figs. 1, 2) The four leg assemblies are packed in a separate carton for shipment. The standard legs (53/8" high) allow the rim of the feed pan on the table model to be 27" above the table surface. These legs have neoprene feet and require assembly. To assemble 53/8" high legs: Slide the Leg Stud through the Leg End Cap and the Leg; then thread the Leg Stud into the base of the machine (Fig. 2). Do not overtighten; the legs need only be hand-tight. Thread the Neoprene Foot into the Leg Stud (Fig. 2). Floor model choppers are equipped with optional 15", 18" or 21" legs. Each Leg is one piece and threads into the base of the machine at the four corners. These Legs can be adjusted by threading the Feet in or out as necessary (Fig. 2) to level and stabilize the chopper. LEG (15", 18" or 21") LEG LEG END CAP LEG STUD NEOPRENE FOOT FOOT PL-56170 Fig. 2 – 3 – ELECTRICAL CONNECTION WARNING: ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THE APPLICABLE PORTIONS OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCAL ELECTRICAL CODES. WARNING: DISCONNECT ELECTRICAL POWER SUPPLY AND PLACE A TAG AT THE DISCONNECT SWITCH INDICATING THE CIRCUIT IS BEING WORKED ON. ELECTRICAL DATA Model Volts / Hertz / Phase Dual Element Time-Delay Fuse Inverse Time Circuit Breaker Minimum Circuit Ampacity AMPS Maximum Fuse Size AMPS 60oC Copper Wire Size Minimum Circuit Ampacity AMPS Maximum Circuit Breaker Size AMPS 60oC Copper Wire Size 200 / 60 / 1 30 30 #10 45 45 #6 4732 230 / 60 / 1 30 30 #10 45 45 #6 4732A 200 / 60 / 3 15 15 #14 25 25 #10 230 / 60 / 3 15 15 #14 25 25 #10 460 / 60 / 3 15 10 #14 15 10 #14 Compiled in accordance with the National Electrical Code, 2002. The junction box is tapped for 3/4" trade size conduit and may be rotated 180o for convenience of installation. THREE PHASE MACHINES Three phase machines must be connected so that the attachment drive runs counterclockwise when facing the hub. To check the direction of rotation, turn the chopper on momentarily. If rotation is not correct, DISCONNECT ELECTRICAL POWER SUPPLY and interchange any two ot the incoming power supply leads. Reconnect power to the chopper. Turn the chopper on momentarily to verify correct motor rotation. OPERATION WARNING: DO NOT OPERATE WITHOUT GUARD OVER FEED OPENING. DO NOT PUT HANDS INTO FEED OPENING. USE FEED STOMPER. After cleaning, assemble chopper Cylinder, Worm, Knife, Plate and Adjusting Ring (and Feed Pan on model 4732A) as discussed in CLEANING, page 7, and Fig. 3 or Fig. 4. Place the Deflector over the Adjusting Ring. • To start the chopper, pull the Start-Stop Switch Knob (Fig. 3 or Fig. 4). • To stop the chopper, push the Start-Stop Switch Knob. The fineness of cut depends on the hole size of the chopper's Plate. T...
Questo manuale è adatto anche per i modelli :Robot da cucina - ML-18887 (553.45 kb)