valutazioni - 4, GPA: 3.3
(
)
)
|
Facilità d'uso
*When charging is completed, the charging light color will change from red to green and a tone will sound steadily for about 5 seconds. After charging, unplug the charger from the power source. Refer to the table below for the charging time. Fast charger DC1201 I 1200 I Approx. 45 min I 1201 / 1201A I ADDrOX. 60 min CAUTION: .The fast charger Model DC1201 is specifically designed to charge only Makita battery cartridges. Never use it for other purposes or for other manufacturer's batteries. When you charge a new battery cartridge or a battery cartridge which has not been used for a long period of time, it may not accept a full charge. This is a normal condition and does not indicate a problem. You can recharge the battery cartridge fully after discharg- ing it completely and recharging a couple of times. 0 If you charge a battery cartridge from a just-operated tool or a battery cartridge which has been left in a location exposed to direct sunlight or heat for a long time, the charg- ing light may flash in red color. If this occurs, wait for a while. Charging will begin after the battery cartridge cools. The battery cartridge will cool faster if you remove the battery cartridge from the fast charger. 0 If the charging light flashes alternately in green and red color and a tone sounds "beep, beep, beep, . . ." for about 20 seconds, a problem exists and charging is not possible. The terminals on the charger or battery cartridge are clogged with dust or the battery cartridge is worn out or damaged. 0 If you wish to charge two battery cartridges, allow 15 minutes between chargings on the fast charger. Removing or installing the saw blade CAUTION : Always be sure that the tool is switched off and the battery cartridge is removed before installing or removing the blade. To remove the blade, press the shaft lock so that the blade cannot revolve and use the hex wrench to loosen the bolt counter- clockwise. Then remove the bolt, outer flange and blade. To install the blade, follow the removal procedure in reverse. BE SURE TO TIGHTEN THE BOLT SECURELY. CAUTION : Fig. 1 0 Be sure the blade is installed with teeth pointing up at the front of the tool. 0 Use only the Makita hex wrench to install or remove the blade. Hex wrench storage I When not in use, the hex wrench can be convenientIy stored. Hex I Fig. li Adjusting the depth of cut Loosen the screw on the depth guide and move the base up or down. You can read the depth of cut by aligning the top of the notch in the depth guide with the graduations on its right side. (Note : This can be done for 0" bevel cutting only.) At the desired depth of cut, secure the base by tightening the screw. Depth guide guide Base 1Screw I Fig. 13 Fig. 14 CAUTION: 0 Use a shallow depth of cut when cutting thin workpiece for cleaner, safer cuts. 0 After adjusting the depth of cut, always tighten the clamp screw securely. Bevel cutting Loosen the screw on the bevel scale plate on the front of the base. Set for the desired angle (0"-45") by tilting accordingly, then tighten the clamp screw securely. Screw Bevel scale plate Fig. l! CAUTION: After adjusting the depth of cut and bevel cutting angle, be sure to tighten the screw. Sighting The front of the base is notched to provide two guide edges. For straight cuts, align the edge with 0' engraved on it with your cutting line on the workpiece. For 45' bevel cuts, align the edge with 45' engraved on it with your cutting line. I For straight cuts \ 'For 450bevel Cutting line Fig. 11 Switch action Lock-off lever To prevent the trigger from being acciden- tally pulled, a lock-off lever is provided. To start the tool, slide the lock-off lever in the direction of the arrow and pull the trigger. Release the trigger to stop. I J Fig. 17 CAUTION : Before inserting the battery cartridge into the tool, always check to see that the switch trigger actuates properly and returns to the "OFF" position when released. Operation Hold the tool firmly. Set the base plate on the workpiece to be cut without the blade making any contact. Then turn the tool on and wait until the blade attains full speed. Now simply move the tool forward over the workpiece surface, keeping it flat and advancing smoothly until the sawing is completed. To get clean cuts, keep your sawing line straight and your speed of IBase advance uniform. Fig. 18 CAUTION: 0 Always gently keep the tool moving straight ahead when cutting. Forcing or twisting the tool will result in overheating of the motor and dangerous kickback, possibly causing severe injury. 0 If the tool is operated continuously until the battery cartridge has discharged, allow the tool to rest for 15 minutes before proceeding with a fresh battery. Guide rule The handy guide rule allows you to do extra-accurate straight cuts. Simply slide \A Clamp screw the guide rule up snugly against the side of the workpiece and secure it in position with the clamp screw on the front of the base. It also makes repeated cuts of uni- form width poss...
Questo manuale è adatto anche per i modelli :Jig Saw e - 5091DWG (915.95 kb)