. . . . . . . . . . . . . . . . .3 Table Extension . . . . . . . . . . . . . . . . . . . . . .5 Rallonge laterale de table . . . . . . . . . . . . . .7 Tafelverbreding . . . . . . . . . . . . . . . . . . . . . .9 Allargamento del tavolo . . . . . . . . . . . . . . .11 Extension de la mesa . . . . . . . . . . . . . . . .13 Alargador da bancada . . . . . . . . . . . . . . . .15 Bordforbredelse . . . . . . . . . . . . . . . . . . . . .17 Bordforlengelse . . . . . . . . . . . . . . . . . . . . .19 T

Max. saw blade O 250 mm Saw blade arbor bore O 30 mm Max. blade speed 4000 min-1 Max. depth of cut 80 mm Safety devices Riving knife The riving knife prevents the workpiece from being caught by the rising teeth of the saw blade and being thrown against the operator. Always have riving knife installed during operation. Blade guard The blade guard protects against accidental contact with the blade and keeps chips from flying about. Always have blade guard installed during operation. Push stick The

Saw blade change ADanger! Risk of injury by the saw blade’s teeth. Wear gloves when changing blades. 1. Remove the two fastening screws of the removable table section. 2. Lift removable table section up and remove. 3. Raise blade fully. 4. Take blade guard off. 5. Lift chip case cover slightly and swing to the side. The cover is hooked into the bottom of the chip case and can not fall down. 25 20 15 10 5 0 30 35 2.10 PK 255 6. To block the saw blade insert lock bar into hole in the saw table and

370 m/min for hard wood, plastics and non-ferrous metals (with special band saw blade); . 800 m/min for all kinds of wood. A Caution! The drive belt must not run in a diagonal position; this will damage the belt Setting knob for drive belt tension With the setting knob (30) the drive belt tension is corrected, if necessary: . turning the setting knob clockwise lessens the blade tension; . turning the setting knob counterclockwise increases the blade tension. Saw table tilt After loosening the lo

1. Remove table insert (80) from saw table (push up from underneath). 2. Fit new table insert. 9.7 Saw Cleaning 1. Open the lower housing door. 2. Remove the chip case (81) and empty it. 3. Remove chips and saw dust with brush or vacuum from: . inside of the lower band saw housing; . blade guides; . operating elements 4. Swing door catch lever (82) up and put the chip case back in. 9.8 Saw storage ADanger! Store saw so that . it can not be started by unauthorized persons and . nobody can get hur

D ENG ENG ENG GENERAL SAFETY INFORMATION As with all power tools there is a certain amount of hazard involved with the operator and his use of the machine. Using the machine with the respect and caution demanded as far as safety precautions are concerned will considerably lessen the possibility of personal injury. If, however, normal safety precautions are overlooked or completely ignored, personal injury to the operator can develop. 1. FOR YOUR OWN SAFETY READ AND UNDERSTAND THIS INSTRUCTION MA

The gap between riving knife and blade must not exceed 10mm/3/8 “. Do not set top of riving knife lower than 2mm-5/64” below the blade’s crown. 9.2 Blade Change Disconnect from power before servicing! Remove chip case lid and loosen arbor bolt. Remove arbor bolt and counter flange, then take off blade. Note: Arbor bolt has L.H. thread, turn clockwise to loosen. Before installing new blade clean blade seat and apply a light coat of oil to the arbor bolt. - Be sure that teeth are pointing in