Additional cable grommets can be purchased through Garmin or a Garmin dealer. When installing the power/network cable, observe the following: • To ensure safety, use the appropriate tie-wraps, fasteners, and sealant to secure the cable along a route and through any bulkhead or deck. Avoid running the cable near moving objects, high-heat sources, or through doorways and bilges. • Avoid installing the cable next to or parallel to other cables, such as radio antenna lines, or power cables. This is

If the handheld compass does not point north when you hold it in the location you want to mount the CCU, then there is magnetic interference. Choose another location and test again. GHP 10 Marine Autopilot System Installation Instructions Opening for cablesMounting screws (. ) ThumbscrewOpening for cables Mounting screws (. ) Thumbscrew 26 GHP 10 Marine Autopilot System Installation Instructions If possible, mount the CCU within 16 ft. (5 m) of the ECU. If you cannot mount the CCU within 16 ft.

Visit the Garmin Web site (for current updates and supplemental information concerning the use and operation of this and other Garmin products. Garmin®, GPSMAP®, AutoLocate®, TracBack®, BlueChart®, and MapSource® are registered trademarks of Garmin Ltd. or its subsidiaries and may not be used without the express permission of Garmin. December 2006 Part Number 190-00665-00 Rev. B Printed in Taiwan IntroductIon > InstallIng Your gMr 21/41 and about thIs Manual IntroductIon This manual covers the f

To connect the VHF 300 series radio to your existing NMEA 2000 network: 1. Determine where you would like to connect the radio to your existing NMEA 2000 backbone. 2. Disconnect one side of a NMEA 2000 T-connector from the backbone at an appropriate location. If you need to extend the NMEA 2000 backbone, connect an appropriate NMEA 2000 backbone extension cable to the side of the T.connector you disconnected. 3. Add a T.connector (not included) for the radio to the NMEA 2000 backbone by connecti

Before you begin the installation: • Read these instructions thoroughly. • Gather the appropriate fasteners and tools. • Verify that all cables can reach the radio mounting location. • Wear safety goggles and a dust mask when drilling, cutting, or sanding. Product Registration Help us better support you by completing our online registration today. Go to Keep the original sales receipt, or a photocopy, in a safe place. Contact Garmin Contact Garmin Product Support if you have any questions while

The GMI 10 will communicate with NMEA 2000- or NMEA 0183-compatible sensors and devices, and can show information such as speed, heading, water depth, and fuel information when connected to the appropriate sensors. Product Registration Help us better support you by completing our online registration today. Go to Keep the original sales receipt, or a photocopy, in a safe place. For future reference, write down the serial number assigned to your GMI 10 in the space provided below. The serial numbe

Your radio includes full Class D DSC capabilities. If you have a GPS device connected to the transceiver, your latitude and longitude and the current time are transmitted when you send a distress call or other type of DSC call. If you have manually entered your position information, your latitude, longitude, and time of entry are transmitted with the call. Having your location automatically transmitted prevents you from needing to identify your location in an emergency situation. Channel 70 is r

The scanner is automatically powered on with the MFD. The Welcome Page appears showing the GMR 21 or GMR 41 as a detected network connection. 2. Press ENTER when I Agree turns yellow, then press PAGE until the Radar Page appears. 3. During Standby mode, a countdown appears on the Radar Page and the status bar as the scanner prepares to operate. 4. With the scanner Ready, press and hold the FCTN key until Do you want to begin radar transmission? appears. 5. When safe (personnel are clear of the r

NOte: on a 4000 or 5000 series chartplotter, your service package appears on the system information screen (Configure > System > System Information > Weather Subscription) XM Radio: Highlight the Audio sub tab and verify that channels 7, 9, 47, and 122 are being received (see page 22). This indicates that all channels on XM’s basic radio service are being received. If within an hour the XM WX Weather and/or the XM Radio service has not activated, call XM customer care at 800-985-9200 to refresh

To complete the installation, you need the appropriate fasteners, tools, and mounts. These items should be available at most marine dealers. Always wear safety goggles, ear protection, and a dust mask when drilling, cutting, or sanding. When drilling or cutting, always check first to see what is on the other side of the surface. If you experience difficulty with the installation, contact Garmin Product support or seek the assistance of a professional installer. Installation Guidelines In order t