valutazioni - 3, GPA: 4
(
)
)
|
Facilità d'uso
Tuner reception 1 Adjust the source selector to FM or AM. 2 Turn TUNING to tune to a station. • For FM, pull out the telescopic antenna. Incline and turn the antenna. Reduce its length if the signal is too strong (very close to a transmitter). • For AM, the set is provided with a built-in antenna so the telescopic antenna is not needed. Direct the antenna by turning the whole set. 3 To switch off the radio, adjust the source selector to OFF position. CD player Display indication for CD functions: – OO: Cd door open – --: reading disc contents / no disc/ error in CD operation or with the CD/ CD-R/W is blank or not finalized (see Troubleshooting) – In stop mode: total track number – During CD playback: 9 and current track number – 2: playback on pause – PROG: when CD program active Playing a CD This CD player plays Audio Discs including CD-Recordables and Rewritable. • MP3 CD-ROMs, CD-I, CDV,VCD, DVD or computers CDs are not possible for playback. 1 Adjust the source selector to CD. 2 Open the CD door, and insert a CD/ CD-R/W with the printed side facing up and press the CD door gently close. 3 Press PLAY/ PAUSE 2; on the set to start playback. 4 To pause playback, press PLAY/ PAUSE 2;. . 2 flashes. 5 To resume, press PLAY/ PAUSE 2; again. 6 To stop CD play, press STOP 9. 7 To switch off the set, adjust the source selector to OFF position and check if the cassette keys are released. Note: CD play will also stop when: -- you open the CD compartment; -- you select FM or AM sound source; -- the CD has reached to the end. Selecting a different track During playback you can use ./ § to select a particular track. – If you have selected a track number in the stop or pause position, press PLAY/ PAUSE 2; to start playback. • Press § once briefly for the next track, or press repeatedly until the desired track number appears in the display. • Press . once briefly to return to the beginning of a current track. • Press . more than once briefly for a previous track. Finding a passage within a track 1 During playback, press and hold down ./ §. • The CD is played at high speed and low volume. 2 When you recognize the passage you want release ./ §. 3 Normal playback resumes. Note: When searching within a final track and you reach the end of the last track, the CD goes to stop mode. Programming track numbers You may store up to 20 tracks in the desired sequence. If you like, store any track more than once. 1 In the STOP position, press PROGRAM to activate programming. . Display: shows 01 indicating the start of the program. PROG and 01 flash. 2 Press . or § to select your desired track number. 3 Press PROGRAM to store the desired track number. . Display shows 02 and flashes (up to 20 in sequence) indicating the next available program location. 4 Repeat steps 2 to 3 to select and store all desired tracks in this way. . If you attempt to store more than 20 tracks, no track can be selected and the display will review your programmed tracks. 5 To play your program, press PLAY/ PAUSE 2;. To review your set program In the stop position, press PROGRAM once. . Display shows the stored tracks in sequence. Erasing a program You can erase the contents of the memory by: – press STOP 9 (twice during playback or once in the stop position; – selecting FM or AM sound source; – opening the CD door. . Display: PROG disappears. Environmental information All unnecessary packaging material has been omitted.The packaging can be easily separated into three materials: cardboard, polystyrene and plastic. Your set consists of materials which can be recycled if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packaging, dead batteries and old equipment. If a fault occurs, first check the points listed below before taking the set for repair. If you are unable to remedy a problem by following these hints, consult your dealer or service centre. WARNING: Under no circumstances should you try to repair the set yourself, as this would invalidate the warranty. Problem Solution No sound/power – Volume not adjusted. Adjust the VOLUME. – Power cord not securely connected. Connect AC power cord properly. – Batteries dead /incorrectly inserted. Insert (fresh) batteries correctly. Display does not function – Electrostatic discharge. properly/ No reaction to Switch off and unplug the set. operation of any of the Reconnect after a few seconds. controls Display and CD playback – No CD inserted. Insert a CD. does not work – CD badly scratched/ dirty. Replace/ clean CD (see Maintenance). – Laser lens steamed up. Wait until lens has acclimatized. – CD-R/W is blank or not finalized. Use a finalized CD-R/W or suitable audio disc only. The CD skips tracks – Disc damaged or dirty. Replace or clean disc. – Program is active. Quit program mode. English Controls Power Supply Power Supply General Operation CD player CD player Maintenance Troubleshooting IMPORTANT SAFETY INSTRUCTIONS • Once your Magnavox purchase is registered, ...
Questo manuale è adatto anche per i modelli :Ricevitori - MCS210SL (1.97 mb)