valutazioni - 4, GPA: 3.3
(
)
)
|
Facilità d'uso
(In the B version, it is necessary to turn the deck POWER switch ON.) Automatic Source Selection (COMPU LINK-1, 3) When the provided remote cables are used for connecting this unit to other components which have COMPU LINK-1 or 3/SYNCHRO terminals, the switch-over of all system components is possible with simple one-touch of the source selector button of JVC’s amplifier or receiver. By doing this, the corresponding component will start playing automatically. The source select button of the remote control unit or the activation button of the desired component can be also used for this purpose. When the components have been switched over, the previous component will stop playing within five seconds. Synchronized Recording (COMPU LINK-1, 3) Synchronized recording refers to the process in which the deck starts recording in synchronism with the CD player. Perform the synchronized recording as follows: 1. Set the cassette deck to the record-pause mode in accordance with the recording procedures on page 8. 2. If you want the programmed recording, program the desired tunes in any order you wish to hear. 3. Press the PLAY/PAUSE button of the CD player. By so doing, the cassette deck is placed in the record mode and synchronized with the CD player for recording. Synchronized recording thus can be made possible. DDRP (Dynamics Detection Recording Processor) recording The DDRP function makes possible fully automatic recording when used with a suitable JVC CD player. When the DDRP button of a suitable JVC CD player is pressed, the recording level is first adjusted automatically, then recording starts; it is not necessary to start recording by the normal procedure. • Synchronized recording or DDRP recording stops automatically when the CD player stops playing. • Synchronized recording does not start except when the record- pause mode is set by simultaneously pressing the REC/REC MUTE and PAUSE buttons in the stop mode. • To cancel synchronized recording or DDRP recording, press the STOP button of the CD player or cassette deck. • The source is locked to the CD position during synchronized recording or DDRP recording to avoid accidental stops or switch-over to another component. To switch over the components, cancel synchronized recording or DDRP recording first. • The INPUT LEVEL control does not function during DDRP recording. –11– DUBBING • Synchro dubbing Operate in the order of the numbers in the illustration. 1 POWER OFF STANDBY / ON (B version) POWER (J version) 2 A 3 A 4 REVERSE MODE 5 COUNTER RESET 6 A B SYNCHRO DUBBING NORM SPEED HIGH SPEED 7 1 Turn the power on. 2 Insert a prerecorded tape with side A facing out into deck A, and press the (direction) button to select the travel direction. 3 Insert the blank tape with side A facing out into deck B, and press the (direction) button to select the side to be recorded. 4 Select the REVERSE MODE. 5 Press to ‘‘00 00’’. (Deck B) 6 Press the SYNCHRO DUBBING (NORM or HIGH SPEED) button to start dubbing. 7 Press the (stop) button of deck B to stop dubbing. When deck B stops, the dubbing mode is automatically released. • Synchro record muting When deck A stops or enters any mode other than the playback mode during dubbing, deck B enters the record mute operation automatically and then enters the record-pause mode. • Before pressing the SYNCHRO DUBBING button Confirm that deck B is in the stop mode before starting dubbing. Dubbing and DOLBY NR button During dubbing, the same NR mode selected for the playback cassette is applied to the recording cassette, regardless of the setting of the NR button. Input level Recording is performed at the same level as the playback tape during dubbing regardless of the position of the INPUT LEVEL control. Microphone mixing during dubbing By connecting a microphone, microphone mixing during dubbing is possible with the playback sounds from deck A. Be sure to perform dubbing at normal speed. When performing microphone mixing during dubbing, use cassettes recorded with NR OFF mode for the deck A. Tape editing 1. Press the REC/REC MUTE button when finished dubbing a tune. Deck B automatically enters the record muting mode and leaves a non-recorded section of about 4-seconds then enters the record-paused mode. 2. Press the (stop) button of deck A and search for the next tune you want by using the , or PLAY button. Then stop the cassette just before the beginning of the tune. 3. Press the same SYNCHRO DUBBING button pressed before the pause again, and dubbing will start. Notes at dubbing 1. Normal-speed dubbing is recommended to obtain good sound quality. 2. Television receivers placed close to the deck may cause interference on the recorded signal when the deck is used in the high-speed dubbing mode. If this happens, either turn off the television receiver or use the normal-speed dubbing mode. –12– MAINTENANCE The importance of cleaning When the tape is moving, magnetic powder and dust naturally accumulate on the heads, capstan and pinch roller....