valutazioni - 0, GPA: 0
(
)
)
|
Facilità d'uso
If your water is very hard, we recommend that you use softened water. You can only dispense with descaling completely if you exclusively use softened water. If this is the case, change the water hardness to " softened" . You can change the water hardness range in the basic settings when the appliance is switched off. 1. If required, press the % button to switch off the appliance. 2. Press and hold the ° button until “ Select language” appears in the display. 3. Press the X button until “Water hardness” appears. “ 2- medium” is highlighted in the display. 4. Change the water hardness using the rotary selector. Possible values: softened 1-soft I 2-medium II 3-hard III 4very hard IV 5. Press the ° button to exit basic settings. The change is saved. Before first use Before first use, heat the empty appliance for 20 minutes at 100 °C with the Steam type of heating. Do not open the appliance door during this time. The appliance is automatically calibrated ( see section: Automatic calibration) . 1. Press the % button to switch on the appliance. The "Hot air" type of heating appears after approx. 4seconds. 2. Fill the water tank and insert it (see section: Filling the water tank) . Before using for the first time, moisten the tank cover seal with a little water. 3. Turn the rotary selector until "Steam" appears. 4. Press the n button. The appliance heats up to 100 ° C. The cooking time ( 20 minutes) does not start to count down until the set temperature has been reached. Do not open the appliance door during this time. The cooking operation automatically ends and a signal sounds. 5. Press the % button to switch off the appliance. Leave the appliance door ajar until the appliance has cooled down. Cleaning the accessories before use Using soapy water and a soft cloth, clean the accessories thoroughly before first use. Fitting the grease filter in place : Risk of injury! Hook the enclosed grease filter onto the hot air grille in the You could hurt yourself on the grease filter hooks. Always clean back wall of the cooking compartment. the grease filter with care. Always place the grease filter in the Leave the grease filter in the cooking compartment for all dishwater so that the hooks for fixing it in place are facing applications. downwards. Clean the grease filter with hot soapy water or in the dishwasher every time heavy dirt deposits have been left behind after cooking. Operating the appliance In this section, you can read about ¦ how to fill the water tank ¦ how to switch the appliance on and off ¦ what to note after each use ¦ how you can use the recommended settings Filling the water tank When you open the appliance door, you will see the water tank on the right- hand side. Caution! Use of unsuitable liquids may damage the appliance ¦ Only use fresh tap water, softened water or uncarbonated mineral water. ¦ If your tap water is very hard, we recommend that you use softened water. ¦ Do not use distilled water, highly chlorinated tap water (> 40 mg/l) or other liquids. You can obtain information about your tap water from your water supplier. The water hardness can be checked with the test strips enclosed. Fill the water tank before each use: 1. Open the appliance door and take out the water tank (fig. A) . 2. Fill the water tank with cold water up to the “ max” mark ( fig. B) . %& 3. Close the tank cover until you feel it engage. 4. Slide in the water tank all the way (fig. C) . ' The tank must be flush with the water tank recess ( fig. D) . Switching on the appliance Note: Always use the cooking container and wire rack in their standard position (not the other way up). 1. Press the % button to switch on the appliance. The button description appears in the display for approximately 4 seconds. The display then switches automatically to the “ Types of heating” menu. Or press the abutton to go directly to the “ Types of heating” menu. 2. Turn the rotary selector to set the desired type of heating. ! " # $ 3. Press the X button. The default temperature is highlighted. 4. Turn the rotary selector to set the desired temperature. Type of heating Temperature range Default cooking time Hot air 30 - 230 ° C - Steam 35 - 100 ° C 20 minutes Combination 120 - 230 ° C 30 minutes Reheat 100 - 180 ° C 10 minutes Prove 35 - 50 ° C 30 minutes Defrost 35 - 60 ° C 30 minutes Slow cooking 60 - 120 ° C - Plate warming 30 - 70 ° C - Keep warm 60 - 100 ° C - For types of heating involving steam, you must now set a cooking time (see also section: Time-setting options) . 5. Press the 0 button. The default cooking time is highlighted. 6. Turn the rotary selector to set the required cooking time. 7. Press the n button to start the cooking operation. The appliance heats up. For the Steam type of heating, the cooking time only starts counting down after the heating- up time is complete. "Fill water tank?" message This message appears if you set a type of heating and the water tank is only half full. If you think that the water in the wate...