Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you. Form: SP-100-E - 4/25/96 3 SAFETY GUIDELINES - DEFINITIONS This manual contains information that is important for you to know and understand. This information relates to protecting YOUR SAFETYand PREVENTINGEQUIPMENT PROBLEMS. To help you recognize this information, we use symbols to the right. Please read the manual and pay attention to these sections. URGENT SAFETY INFORMAT

Operating unit with water supply shut off (without flow of water) will result in equipment damage. During shut-down, entire system including pump, hose and wand will remain under pressure. Do not attempt to remove hose/gun until pressure is relieved. 7 MAINTENANCE AND STORAGE TO AVOID ELECTRICAL SHOCK, ALWAYS DISCONNECT THE PLUG FROM THE ELECTRICAL SUPPLY BEFORE ANY MAINTENANCE IS STARTED. MAINTENANCE 1. WATER SCREEN: Inspect the water screen before attaching water supply. Clean water screen if

WEIGHT W1218 1250 P.S.I. MAX 1.8 G.P.M. 120V/15 AMP/60HZ 15 AMP., TIME DELAY 35' WITH GFCI (GROUND FAULT CIRCUIT INTERRUPTER) 25' SWIVEL HIGH PRESSURE HOSE 40 LBS. SPECIFICATION CHART IMPORTANT: READ AND RETAIN THE SAFETY GUIDELINES AND ALL INSTRUCTIONS CAREFULLY BEFORE OPERATING OWNERS MANUAL FOR PRESSURE WASHER Model No. W1218 MODEL PUMP PRESSURE FLOW RATE VOLTAGE REQUIREMENT MINIMUM FUSE SIZE POWER CORD HOSE PKG. WEIGHT W1218 1250 P.S.I. MAX 1.8 G.P.M. 120V/15 AMP/60HZ 15 AMP., TIME DELAY 35'

This device provides additional protection from the risk of electrical shock. (Figure 1) FLOW RATE: This is the amount of water that passes through your wand. (Usually measured in G.P.M., gallons per minute.). IDLE MODE: This pertains to the time that the pressure washer is running without the trigger on the wand engaged to spray. You should never run this pressure washer for more than 5 minutes without pulling the trigger to relieve pressure. Running the pressure washer in this manner would voi

. . . . . . . . . . .2 CONSUMER SAFTEY INFORMATION . . . . .2 SAFETY GUIDELINE/DEFINITIONS . . . . . . .3 IMPORTANT SAFETY INSTRUCTIONS . .3-5 CARTON CONTENTS . . . . . . . . . . . . . . . . . .6 ASSEMBLY INSTRUCTIONS . . . . . . . . . . .7-8 OPERATING INSTRUCTIONS . . . . . . . . .8-12 MAINTENANCE . . . . . . . . . . . . . . . . . . .13-14 STORAGE . . . . . . . . . . . . . . . . . . . . . . . . . . .15 TROUBLE SHOOTING GUIDE . . . . . . .16-17 WARRANTY . . . . . . . . . . . . . . . . . . . . .

2. Exhaust Muffler-Allows hot exhaust to exit the engine. 3. Siphon Tube & Filter- Used to pick up detergents, degreasers, etc. for cleaning. 4. High Pressure Hose-25' x 1/4" dia. high pressure hose used to transport water from pump to gun. 5. Quick Connect Coupler-Used to attach water hose to pump. 6. Pressure Washer Gun-Used to control flow of water coming from pump. 7. 3.5 HP Tecumseh Engine- This engine is shipped without oil. Included with this pressure washer is a copy of the Engine Manufa

4. Flush wand assembly backwards with water or compressed air. 5. If pressure is still too high, repeat steps 2-4. 4. CHECKING OIL: The pump is shipped with the correct amount of oil in it. This pump should never need any oil added or changed unless it develops a leak. A 30 weight non- detergent oil can be used in this pump (approximately 6 oz.). If pump is leaking oil take to an Authorized Service Center. HIGH PRESSURE HOSE: Damaged high pressure hoses can burst which can cause a potentially ha

NOTE: The meter housing will be full of liquid so some means should be available to catch what drains from the case and lines. To remove gears (22-25), remove three retaining rings (20) and drive key (21). Withdraw the drive shaft and gear (14), spacer (15), and all parts of bearing and seal assembly (26). Remove the nylon washer from item 26 and note its location. Remove both oilite bearings and both O-rings from bore in register housing. Using new parts, which consist of a new nylon washer, 2

NOTE: Elbow fitting is not required, however, it provides strain relief for the hose. 2. Screw the hose into the open end of the elbow and tighten. Apply gasoline-resistant pipe compound to male threads. 3. Screw nozzle onto hose. NOTE: 1820R models are shipped with a vacuum breaker assembly (P/N 032701) consisting of a tee, pipe nipple and vacuum breaker. This assembly should be installed in the pump outlet before connecting the hose. 2-4 9312 Installation Direct Mount on Underground Tanks 1. S