LIMITATIONS AND EXCLUSIONS: This Limited Warranty shall not apply to: 1. Bent or broken crankshaft or resultant damage caused by vibration related to a bent or broken crankshaft Also, damage caused by loose engine mounting bolts or improper or imbalanced accessories or blades mounted to the crankshaft. 2. Repairs required because of prolonged storage including damage caused by old or contaminated fuel in the fuel tank, fuel lines, or carburetor, sticky valves or corrosion and rust of engine part

Check the air filter monthly. For best performance, replace the air filter at least once a year. n Unscrew air filter knob, then remove the air filter cover. n Lift the edge of the air filter carefully and pull it out. n Wash the air filter with warm, soapy water. n Rinse and squeeze to dry. n Reinstall the air filter. NOTE: Make sure the filter is seated properly inside the cover. Installing the filter incorrectly will allow dirt to enter the engine, causing rapid engine wear. n Reinstall the a

20 hrs. 50 hrs. 100 hrs. 300 hrs. Clean engine & check bolts & nuts X X Check engine oil X Change engine oil* X Clean spark plug X Clean air cleaner X X Replace air cleaner element X Clean & adjust spark plug & electrodes X Replace spark plug X Remove carbon from cylinder head** X Check & adjust valve clearance** X * Initial oil change should be performed after the first 20 hours of operation. Do not pour old oil down sewage drains, into garden soil, or into open streams. Your local zoning or en

3 Fig. 2 Fig. 4 B C A D E C A D B A B A - Handle spacers (espaceurs de la poignee, espaciadors de la mango) B - Handlebar (poignee du guidon, mango) C - Handle knob (verrou de la poignee, perilla del mango) D - Acorn nut (ecrou borgne, tuerca ciega) E - Handle bolts retracted until flush with spacer (boulons de poignee rentre a affleurement avec espaceur, pernos del mango retraidos hasta alinearse con el espaciador) A -Phillips screwdriver (tournevis phillips, destornillador phillips) B - Adjust

This secures the spray wand in place. CONNECTING HIGH PRESSURE HOSE TO TRIGGER HANDLE See Figure 6. n Screw the collar on the high pressure hose into the trigger handle inlet coupler by turning the hose collar clockwise. n Pull on the hose to be certain it is properly secured. ATTACHING INJECTION HOSE See Figure 7. Before detergent can be used with this machine, the injection hose must be attached. n Push the injection hose filter onto the end of the injection hose (if not already installed). n

. Keep guards in place and in working order. Never operate the tool with any guard or cover removed. Make sure all guards are operating properly before each use. . Remove adjusting keys and wrenches. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. . To reduce the risk of injury, keep children and visitors away. All visitors should wear safety glasses and be kept a safe distance from work area. . Keep the area of operation clear of all pe

When adding gas to the pressure washer, make sure the unit is sitting on a flat, level surface. If the engine is hot, let the pressure washer cool before adding gas. ALWAYS fill the fuel tank outdoors with the machine turned off. NOTE: Use unleaded gas only. DO NOT mix lubricant with gas. n Before removing the fuel cap, clean the area around it. Remove the fuel cap. n Insert a clean funnel into the fuel tank then slowly pour gasoline into the tank. Fill tank to approximately 1-1/2 in. below the

9 Fig. 15 Fig. 12 B C A B A C B A A - Trigger (gachette, gatillo) B - Slot (fente, ranura) C - Lock Out (bouton de verrouillage, seguro) A - Fuel Valve (robinet de carburant, valvula de combustible) B - ON position (marche, encendido) C - OFF position (arret, apagado) Fig. 16 A - Water intake (rise d’eau, entrada de agua) B - Garden hose (tuyau d’arrosage, manguera de jardin) Fig. 13 F 25 Fig. 10 A B E C C B A G A - Choke lever (levier d’etrangleur, palanca del anegador) B - OFF (RUN) position (

Maintenance items not listed here should be performed by a service center. Page 15 — English TROUBLESHOOTINGTROUBLESHOOTING PROBLEM CAUSE SOLUTION Engine fails to start 1. No fuel in tank 2. Spark plug shorted or fouled 3. Spark plug is broken (cracked porcelain or electrodes broken) 4. Ignition lead wire shorted, broken, or disconnected from spark plug5. Ignition inoperative 6. Unit is not primed. 1. Fill tank 2. Replace spark plug 3. Replace spark plug4. Replace lead wire or attach to spark pl

OWNER’S WARRANTY RESPONSIBILITIES As the engine owner, you are responsible for the performance of the required maintenance listed in your owner’s manual. ROBIN AMERICA recommends that you retain all receipts covering maintenance on your engine, but ROBIN AMERICA cannot deny warranty solely for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance. As the engine owner, you should however be aware that ROBIN AMERICA may deny warranty coverage if your engin