• Disconnect the high pressure hose and the garden hose. 5.6 HOSE REEL KIT Insert the high pressure hose nut coupler (Fig.24) into the slot in the hose reel. Hold the hose firmly into the slot. At the same time, turn handle in the direction shown (Fig. 25). Allow hose to slide through hand applying slight resistance for proper coiling. Stop winding hose 2 ft. (60 cm) from gun to provide enough slack to store gun in holder located on the docking station. See page 6, #27 for storage location. 16 E

Never use Bleach, Ammonia or Hot water in the unit. The part will have to be replaced, Please email us directly at: customerservice@huskypowerwasher.com. You can also order the part directly at: Check that the circuit is rated at 1 amps or Circuit breaker trips or Fuse blown in Fuse box Extension cord too long or wire size too small Nozzle partially blocked Excessive pressure greater. Make sure the unit is plugged into a dedicated circuit. Use proper extension cord as recommended in Owner’s Manu

4. Turn the machine OFF and squeeze the trigger to release the trapped pressure inside of the machine. 5. Remove both the garden hose and high pressure hose from the unit. 6. Turn ON the machine and allow it to run for 5 seconds. (This will clear out most of the water trapped in the pump). 7. Unplug the machine and store in a dry, climate controlled environment. Do not store the machine or accessories in a place where the temperature could drop below 40°F. Instrucciones de almacenaje y finalizac

Use only EXCELL branded accessories rated equal to or greater than the rating of the pressure washer. REPAIRS To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be performed by an Authorized Warranty Service Center. Always use identical replacement parts. For the location of the nearest Authorized Warranty Service Center call 1-800-888-2468 or visit our website excellpressurewasher.com. 17 - ENG A20116 TROUBLE SHOOTING GUIDE TROUBLE SHOOTING GUIDE CAUSE CORRECTI

21-39 Espanol ............................................ 40-60 IMPORTANT Please make certain that the person who is to use this equipment carefully reads and understands these instructions before operating. IMPORTANT Assurez-vous que toute personne qui utilisera cet equipement lise attentivement ces instructions avant de l’utiliser. IMPORTANTE Asegurese de que la persona que va a usar esta herramienta lea cuidadosamente y comprenda estas instrucciones antes de utilizarla. Part No. A20116 Rev.

NOTE: Cone side faces out. Filter Screen 5. Connect water source to pump inlet. NOTE: Water source must provide a minimum of 5 gallons per minute at 20 PSI. High Pressure Hose Hook-up Water Source To reduce the possibility of contamination always protect against backflow when connected to a potable water system. 6. Connect high pressure hose to pump outlet. 7. If applying a chemical or cleaning solution, see How To Apply Chemicals/Cleaning Solvents instructions in this section. 8. Turn water sou

TO USE GATLING™ SPRAY WAND The nozzles for the spray wand are stored in the gatling spray wand. See chart to choose the correct nozzle for the job to be performed. CHANGING NOZZLES ON SPRAY WAND Risk of fl uid injection. Do not direct discharge stream toward persons, unprotected skin, eyes or any pets or animals. Serious injury will occur. R isk of fl uid injection. Do Not attempt to change nozzles while pressure washer is running. Turn engine off before changing nozzles. 1. Press turret release

Copyright. All Rights Reserved. Este producto se encuentra cubierto por patentes de EE.UU. y otras internacionales. Copyright. Todos los derechos reservados Warranty Registration by Internet Registro Garantia mediante Internet Internet Address: Sitio Internet: SEE OUR WEB SITE FOR REPLACEMENT, MISSING PARTS AND TROUBLESHOOTING VISITEN NUESTRO SITIO WEB PARA SUSTITUCIONES Y/O PARTES FALTANTES Your Model Number is: h1600 IMPORTANT Attention Valued Customer: The serial number of your machine and da

Align the collar on the threaded nipple on the pump. . Insert the nozzle on the end of the high pressure hose collar into the threaded nipple. . Turn the collar clockwise to tighten the hose securely to the pump. . Pull on the hose to be certain it is properly secured. CONNECTING THE GARDEN HOSE TO THE PRESSURE WASHER See Figure 8. The water supply must come from a water main. NEVER use hot water or water from pools, lakes, etc. Before connecting the garden hose to the pressure washer: . Run wat