valutazioni - 2, GPA: 4.5
(
)
)
|
Facilità d'uso
• SSH, HTTPS, and program terminal session timeouts are enabled. • ICSP communication protocol between devices: encryption and authentication are enabled. • Minimum password requirement is 8 characters with at least 1 numeric character. • Login failure attempt pauses 4 seconds before another login attempt is allowed. • After 3 consecutive unsuccessful login attempts, login lockout is enabled for 15 minutes. • Login and logout audit logging is enabled. VG-Series Modero Touch Panels Firmware Pages and Descriptions Security Profile Features (Cont.) DOD: • Must be configured from the program terminal. • HTTP, Telnet, and FTP are disabled. • SSH, HTTPS, and program terminal require authentication by an authorized user. • SSH, HTTPS, and program terminal session timeouts are enabled. • ICSP communication protocol between devices: encryption and authentication are enabled. • Minimum password requirement is 8 characters with at least 1 numeric character, one uppercase character, one lowercase character, and one special character, with no duplicate adjacent characters. • Login failure attempt pauses 4 seconds before another login attempt is allowed. • After 3 consecutive unsuccessful login attempts, login lockout is enabled for 15 minutes. • Login and logout audit logging is enabled. • DoD session banner is enabled. Toggling between these three immediately and automatically resets the existing password to the default password for that setting. With an unsecured panel using the Standard Security setting, the default password is 1988. With panels using either the Secure or the DoD settings, the default password is Amx1234! (paying attention to the case of the letters). Entering the existing password will not work and the default will need to be entered at this point will allow access to the Protected Settings page and allow resetting of the password to a new one. If the Security button setting is changed in any way, even if it is toggled back to its original setting, the password is automatically reset to the default for the chosen setting. You MUST use the new default of 1988 (Standard Security) or Amx1234! (Secure or DoD) to re-enter the Protected Settings page. If accessing the touch panel via telnet, both the default user name AND the default password will be changed if the Security button setting has been changed. The defaults are: username: amx password: Amx1234! The correct case must be followed with the username: "AMX" or "Amx" will not work. For more information on configuring AMX devices for a secure environment, please refer to the guide Security Profiles: Configuring AMX Devices For Installation Into a Secure Environment, available at VG-Series Modero Touch Panels Firmware Pages and Descriptions System Settings Page The System Settings page (FIG. 119) sets the Secondary DNS Address information with its corresponding IP communication parameters, NetLinx Master communication settings, and reads the device number assigned to the Modero panel. IP Settings section Master Connection section (NetLinx Master properties) Master Connection features are not saved until the panel is rebooted Red fields are user-editable Blue fields cycle through choices Grey fields are read-only FIG. 119 System Settings page showing default values (reads and assigns values to the panel and Master) The elements of the System Settings page are described in the table below: System Settings Page Elements Back: Saves the changes and returns you to the previously active touch panel page. Connection Status icon: This visual display of the connection status allows the user to have a current visual update of the panel’s connection status regardless of what page is currently active. • A Lock only appears on the icon if the panel has established a connection with a currently secured target Master (requiring a username and password). IP Settings: DHCP/Static IP Address Subnet Mask Gateway Host Name Primary DNS Secondary DNS Domain Sets the IP communication values for the panel and contains: Sets the panel to either DHCP or Static communication modes. • DHCP (Dynamic Host Configuration Protocol) assigns IP Addresses from client stations logging onto a TCP/IP network via a DHCP server. • Static IP is a permanent IP Address that is assigned to a node in a TCP/IP network. Sets the secondary IP Address assigned to the panel. Sets a subnetwork address to the panel. • Subnetwork mask is the technique used by the IP protocol to filter messages into a particular network segment (Subnet). Sets a gateway value to the panel. • Gateway is a computer that either performs protocol conversion between different types of networks/applications or acts as a go-between two or more networks that use the same protocols. Sets the host name of the panel. Sets the address of the primary DNS server used for host name lookups. • DNS (Domain Name System) is software that lets users locate computers on a local network or the Internet (TCP/IP network) by host and ...
Questo manuale è adatto anche per i modelli :Monitor - Modero NXD/NXT-1200VG (4.48 mb)
Monitor - Modero NXD/NXT-1500VG (4.48 mb)